Question about GMC Yukon

1 Answer

How can i set the car to neutral with no key or power?

Posted by paladyn_yaaj on

Ad

1 Answer

steve

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 266 Answers

To get car in neatral ,locate the shift cable or linkage ,either on top of transmission or the side and unhook from the actuator on the trans.block the wheels so car wont roll over you and move lever 3 clicks

Posted on Feb 12, 2011

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No start, no turn over


You need to say what make , model an year vehicle . Not all manufactures do it the same way !

Aug 10, 2016 | Cars & Trucks

1 Answer

Why wont my car start gauges and lights come on but wont crank no power going to soelinoid wire


If the security system has been reset ( no light on/flashing ) you may have a neutral safety switch problem, Will the vehicle crank over in neutral? In most cases, the neutral switch grounds the starter relay and allows it to operate. Does the starter relay connector have 2 powers? One constant and one with key on/cranking? If these power supplies are there, suspect the ground side of the relay to be the problem and possible neutral safety switch

Jan 20, 2016 | 2000 Ford Taurus

1 Answer

91 Mitsubishi Pajero, wont start get power to the power solenoid when turnig the key. What would be causing this problem?


Check the start fuse first. Then try to start it neutral, not park. It could be the fuse, the safety neutral switch, or the ignition switch. My guess would be the neutral saftey switch.

Feb 06, 2015 | Mitsubishi Cars & Trucks

1 Answer

I turn the key and get nothing I have power but no juice is getting to the starter.


Could be the key switch or the neutral safety switch, or a bad connection. Will it crank in neutral ?

Jan 23, 2014 | 1995 Mercury Grand Marquis

1 Answer

GMC 6.0L starter does not engage


To check the starter: key off, transmission in park or neutral, brake set. Pull off the small wire to starter solenoid. Then use a small jumper wire from battery cable post on the starter to the solenoid terminal (can also use a small screwdriver to bridge those terminals). Starter motor should engage the flywheel and spin the engine. If nothing, starter motor or solenoid is bad. If starter works, check for power on the small solenoid wire, with key held in crank. Wire should have power, if not, check start circuit from ignition switch to solenoid-the neutral safety switch is in that circuit.

Dec 11, 2013 | 2003 GMC Sierra 2500HD

1 Answer

I have a 2001 Eclipse that was running fine and 10 minutes later when I went to take off it would not turn over. There is power and when I turn the key there is no draw on it. I don't know if the starter...


Try putting it neutral, if it starts, the neutral safety switch is suspect. If it won't start go back to park, hold the key in the "start" position and slowly move thru the gears, if it clicks at any point (even between positions) go back to that spot. Again the neutral switch. I always do this before I break out with the test equipment. But make sure the emergency brake is set and stand on the brake pedal! Just in case it starts in gear

Oct 14, 2013 | 2001 Mitsubishi Eclipse

1 Answer

2008 impala won't start or shift out of park, key is difficult to remove from ignition.


Sound like a problem with the Neutral Ssafety Switch, this is located on top transmission (generally) and its possible that need some adjust.

Aug 13, 2012 | 2008 Chevrolet Impala

2 Answers

Starter has power to it but has some problem from the key to the starter Does this model have a relay or something?


Check the neutral safety switch,if it is o k,then replace the ignition switch,Not the key cylinder,but the electrical part.

Jan 23, 2010 | 1991 Oldsmobile Ninety Eight Regency

2 Answers

When I turn the key the relay starts to click.


Ford loves that relay.. Jump the two big posts on the relay. the starter should crank. the little post is from your ignition switch. Jumping the two large terminal bypasses the relay. Make sure the vehicle is in neutral with the brake set.Once you know how to do that, try to key dtart in park, then neutral. If it won't do anything, Your neutral safety switch is defective.
If it will start in any gears, again bad neutral switch. Be careful and good luck. Use a jumper cable to jump the two posts. Anything smaller can get you shock or burned.

Sep 19, 2009 | 2002 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...