Does the Jaguar X308 XJ have an air blend door for climate control?

this should help you...

https://www.jaguarforums.com/forum/xj-xj8-xjr-x308-27/xjr-knock-sensor-location-bank-1-a-40357/

Best to you.

Bank 1, Left, Rear

https://www.jaguarforums.com/forum/xj-xj8-xjr-x308-27/cylinder-97509/

lots more information. Misfires seem a common issue.

https://www.google.com/search?q=2000+jaguar+xj8+firing+order

..

hi Tony.
this is all i could find on the internet so not sure if it will be any good to you,plus you could try ebay.
JAGUAR XJ SERIES X308 PARTS SITEMAP
or this link.
tow bar 1998 xj8 jaguar x308 3 2 Google Search

In the trunk (aka Luggage Compartment in England) life the panel to expose the spare tire. Fuse box should be on right side, near bumper. Take off top. Should be fuse 11. 10AMP accessory fuse. Check to confirm with diagram on lid. https://www.jaguarforums.com/forum/attachments/xj-xj8-xjr-x308-27/339d1239001496-cigarette-lighter-fuse-1999-xj8-l-fuse-locations.jpg

2001 jaguar xj fuse box

Yes the blend door is what controls the air temperature at the register outlets. An example would be the temperature control is set to heat, but you only get cold air or slightly warm, then the blend door is not functioning correctly either due to the door actuator being defective or the blend door has become warped and is jammed, in most cases both are the problem. If you do have automatic climate control there can be a problem with the control module as well, but that is the rarer of the problems I have seen. This assumes the heater core is getting hot and it is not plugged.

OBD-II Trouble Code: P0443 Evaporative Emission Control ...

www.obd-codes.com/p0443

P0443 - Evaporative Emission Control System Purge Control Valve Circuit ... P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) ... But, it's also possible to have a lean condition or a rough running engine if the ...Missing: jaguar ‎xj6

P0443 OBD-II Code and Check Engine Light - Jaguar Forums - Jaguar ...

www.jaguarforums.com > ... > XJ XJ8 / XJR ( X308 )

Feb 24, 2014 - Anyone have an idea on where to look for this? Jaguar® Leasing Deals.... P0443 OBD-II Code and Check Engine Light-xj8-purge-valve. .... Newby with air suspension fault, philwarner, XJ XJ6 / XJ8 / XJR ( X350 & X358 ), 7 ...Missing: 1995

Error code p0443..Think dealer is on crack - F150online Forums

www.f150online.com/.../287418-error-code-p0443-think-dealer-crack.h...

Could be the controller or a faulty blend door.
The blend doors direct air thru the heater core and evaporator along with the vents. The controller uses electric motors to change the direction of air flow.

I would repair the problem if I have to disassemble the varioius parts to get at the air doors --- In-Vehicle Temperature Sensor Removal & Installation To Remove:
In-vehicle temperature sensor

1. Remove the climate control head.
2. While pressing the retaining tabs inward, remove the in-car temperature sensor.

To Install:

1. While pressing the retaining tabs inward, install the in-car temperature sensor.
2. Install the climate control head.

---
Air Door Actuators/Motors Removal & Installation Air Inlet Door (Recirculation) Vacuum Motor To Remove:

1. Remove the instrument panel.
2. Remove the air inlet door motor mounting screws. CAUTION
   Do not attempt to bend any part of the air inlet duct door lever.
   
3. Rotate and remove the air inlet door vacuum control motor.

To Install:

1. Rotate and install the air inlet door vacuum control motor.
2. Install and tighten the mounting screws.
3. Install the instrument panel.

Defroster Door Vacuum Motor To Remove:

1. Remove the passenger air bag module from the instrument panel.
2. Disconnect the vacuum line and remove the mounting screws. CAUTION
   Do not attempt to bend any part of the defroster airflow mode door lever.
   
3. Rotate and remove the vacuum control motor from the defrost door lever.

To Install:

1. Rotate and install the vacuum control motor on the defrost door lever.
2. Install and tighten the mounting screws.
3. Connect the vacuum line to the vacuum control motor.
4. Install the passenger's air bag module.

Floor Console Register Duct Vacuum Motor To Remove:

1. Remove the floor console.
2. Remove the right-side instrument panel insulator.
3. Working from the passenger's footwell, disconnect the vacuum hose.
4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
   Do not attempt to bend any part of the floor console register duct door lever.
   
5. Rotate and remove the vacuum control motor from the floor console register duct door.

To Install:

1. Rotate and install the vacuum control motor onto the floor console register duct door.
2. Install and tighten the mounting screws.
3. Connect the vacuum hose to the floor console register duct vacuum control motor.
4. Install the insulator under the dash.
5. Install the floor console.

Panel/Floor (Heater Air Damper) Door Vacuum Motor To Remove:
Panel/floor door vacuum control motor shield

1. Working through the driver footwell, remove the two screws and the shield. CAUTION
   Do not attempt to bend any part of the airflow mode door lever.
   
2. Label and disconnect the two vacuum hoses.
3. Remove the vacuum control motor mounting screws.
4. Lift, rotate and remove the panel/floor (heater air damper) door vacuum control motor from the door lever.

To Install:

1. Install the panel/floor (heater air damper) door vacuum control motor on the door lever.
2. Install and tighten the mounting screws.
3. Connect the vacuum hoses in their original positions.
4. Install the shield on the vacuum motor.

Temperature Blend Door Actuator To Remove:

1. Remove the integrated control panel.
2. Remove the right-side lower instrument panel insulator.
3. Lower the glove compartment.
4. If equipped with Electronic Automatic Temperature Control (EATC), remove the 2 remote climate control module screws and position the module aside.
5. Remove the temperature blend door linkage shield.
6. Disconnect the temperature blend door electrical connector.
7. Remove the temperature blend door actuator mounting screws.
8. Remove the temperature blend door actuator.

To Install:

1. Position the temperature blend door actuator on the plenum.
2. Install the temperature blend door actuator mounting screws.
3. Connect the temperature blend door electrical connector.
4. Install the temperature blend door linkage shield.
5. If equipped with Electronic Automatic Temperature Control (EATC), reposition the remote climate control module and install the 2 mounting screws.
6. Raise the glove compartment.
7. Install the right-side lower instrument panel insulator.
8. Install the integrated control panel.

This is either an out of phase issue or a temperature control blend door or blend door motor actuator problem, it can also be the climate control module in the dash, 1st try disconnecting the battery for 5 min's to re-sync the climate control module, if this fails u will need to find out what blend door is the problem or if they are ok replace the automatic climate control module in the dash