Question about 2002 Ford Escape

2 Answers

No petal after bleeding breaks - 2002 Ford Escape

Posted by Anonymous on


2 Answers

Jeff Lemon

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.


    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

U can buy a bleeder tool to help u but if our resavoir don't go completely dry then u really only need 2 worry bout the brakes u repaired u can gravity bleed a lot of the air out by putting hose on bleeder & opening it with hose in clean jug & make sure to keep checking fluid level so u don't go dry and add more air. Call me if u need any more tips Jeff 601-912-2551

Posted on Nov 08, 2013



  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 112 Answers

Check fluids under hood and make sure the master cylinder isn't also if you bleed your breaks a good rule of thumb is to do all 4 with 2 people one in car and other bleeding and always start with the passenger rear tire then drivers rear and then passenger front and last drivers front and keep master cylinder full between bleeds

Posted on Feb 07, 2011


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

My break pedal goes all the way to the floor . I replaced brake rotors master cylinder, and Break booster. I had to bleed the brake and still pedal still goes to the floor

You still have air in the system.(not bled properly) If you let the Master cylinder drop down to nothing then you need to bench bleed that before bleeding the lines again.

Feb 18, 2016 | Cars & Trucks

1 Answer

Have bleed breaks have no petal whats wrong?

why did you need to bleed brakes in the first place?,most likely gunk has blocked passages in bottom of master cylender or your wheel cyl still leak

Jun 28, 2014 | Jeep Wrangler Cars & Trucks

1 Answer

I have a 2001 Dodge Intrepid and recently replaced the rear break pads. I've noticed that randomly; while, driving and pressing on the break petal, it sinks in slowly. What can I do to fix the problem?...

Check to make sure that you put brake grease on the back of the pad where it meets the caliper. Also, for the brake petal slowly sinking, this is most likely caused from air in the brake line. Make sure you bleed the brake lines and check for any possible leaks.

Oct 07, 2013 | 2001 Dodge Intrepid

1 Answer


Probably will have to bleed the master cylinder.

Sep 25, 2017 | 2000 Chevrolet Blazer

1 Answer

1996 chevy blazer 4wd break petal goes all the way to the floor breaks r good new master cylinder blead all braks 10 times any sugesstins? help!!!

I know there is ABS in that vehicle, you might still have air in the ABS unit, you will need to get a manual that shows you the correct procedure to bleed the brakes. Master installed u need to start the bleed on the bench, then move to the ABS unit then to the individual calipers and/or wheel cylinders if equipped. I think there is a certain way to do it to avoid incorrect bleeding.

But i have also seen bad master cylinders brand new in the box.

Good Luck.

Aug 24, 2010 | 1996 Chevrolet Blazer

3 Answers

No brakes push pedal to floor

leaky rear break cylinder or master cylinder

Oct 02, 2009 | 2001 Chevrolet Blazer

3 Answers


Most likely your vacumn power brake booster has failed. It is not rebuildable. You will need to buy a new one.

Jun 11, 2008 | 1994 Chevrolet Corvette

Not finding what you are looking for?
2002 Ford Escape Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides