Question about 1997 Oldsmobile Achieva

1 Answer

Need head bolt torqe for 3100 and should bolts be dry

Posted by sands58 on

Ad

1 Answer

Duane Wong

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 6,826 Answers

The bolts should have thread lock on them when installing, and the torque is done in 2 steps. 33 ft lbs. and then 90 deg. after that on the second pass. 3.1L Engine CAUTION
Observe all applicable safety precautions when working around fuel. Whenever servicing the fuel system, always work in a well ventilated area. Do not allow fuel spray or vapors to come in contact with a spark or open flame. Keep a dry chemical fire extinguisher near the work area. Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. LEFT SIDE (FRONT)

  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system into a suitable container.
  4. Disconnect the top half of the air cleaner assembly, then remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Disconnect the spark plug wires from spark plugs and looms then route the wires out of the way.
  7. Remove the rocker arm (valve) covers.
  8. Remove upper intake plenum and lower intake manifold.
  9. Remove the left side exhaust manifold.
  10. Remove oil level indicator tube. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  11. Remove rocker arms nut, rocker arms, balls and pushrods.
  12. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To install:
  13. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  14. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP are showing.
  15. Coat the bolt threads lightly with sealer, then install finger-tight.
  16. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  17. Install the pushrods, rocker arms, balls and rocker arm nuts in their proper locations. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  18. Install the lower intake manifold and upper intake plenum.
  19. Install the rocker arm (valve) covers.
  20. Install the oil level indicator tube. Insert the dipstick.
  21. Connect the spark plug wires to spark plugs and looms.
  22. Install the left side exhaust manifold.
  23. Install the exhaust crossover pipe and heat shield.
  24. Refill the cooling system.
  25. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  26. Connect negative battery cable.
  27. Start vehicle and verify that there are no leaks. Fig. 20: Cylinder head mounting and bolt tightening sequence - 3.1L engine need head bolt torqe for 3100 and should bolts be - 86883134.gif
RIGHT CYLINDER HEAD (REAR) CAUTION
Fuel Injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Drain the cooling system.
  4. Remove the top half of the air cleaner assembly and remove the throttle body air inlet duct.
  5. Remove the exhaust crossover pipe heat shield and crossover pipe.
  6. Raise and safely support the vehicle.
  7. Detach the Oxygen (O2) sensor connector.
  8. Disconnect the exhaust pipe from the exhaust manifold.
  9. Remove the right side exhaust manifold.
  10. Carefully lower the vehicle.
  11. Disconnect the spark plug wires from spark plugs and wire looms and route the wires out of the way.
  12. Remove the rocker arm (valve) covers.
  13. Remove upper intake plenum and lower intake manifold. NOTE: When removing the valve train components they must be kept in order for installation in the same locations they were removed from.
  14. Remove rocker arms nut, rocker arms, balls and pushrods.
  15. Unfasten the cylinder head bolts evenly, then remove the cylinder head from the engine compartment. Remove and discard the gasket. To Install:
  16. Clean all the gasket surfaces completely. Clean the threads on the cylinder head bolts and block threads.
  17. Place the cylinder head gasket in position over the dowel pins on the cylinder block so the words THIS SIDE UP showing.
  18. Coat the bolt threads lightly with sealer, then install finger-tight.
  19. Tighten the cylinder head bolts in sequence to 33 ft. lbs. (45 Nm). With all the bolts tightened make a second pass tightening all the bolts an additional 90°.
  20. Install the pushrods loosely retained with the rocker arm assemblies. Make sure all pushrods are in the correct locations. Coat the ends of the pushrods with prelube. The intake rods are marked yellow and are 5 3?4 inch long. The exhaust pushrods are marked green and 6 inches long. balls and rocker arm nuts. Tighten the rocker arm nuts to 18 ft. lbs. (25 Nm).
  21. Install the lower intake manifold and upper intake plenum.
  22. Install the rocker arm (valve) covers.
  23. Connect the spark plug wires to spark plugs and wire looms.
  24. Raise and safely support the vehicle.
  25. Install the exhaust manifold.
  26. Connect the exhaust pipe to the exhaust manifold.
  27. Carefully lower the vehicle.
  28. Connect the Oxygen (O2) sensor wiring.
  29. Install the exhaust crossover pipe and heat shield.
  30. Refill the cooling system.
  31. Install the top half of the air cleaner assembly and the throttle body air inlet duct.
  32. Connect negative battery cable.
  33. Start vehicle and verify that there are no leaks.
prev.gif next.gif

Posted on Feb 04, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need torq specs and pattern on a 2003 s10 2.2L Main bearings, rod bearings and head bolts, Thank you


Main bearings--31 ft lbs then turn 70 degrees.
rod bearings--38 ft lbs.
First step--Cylinder head-- short bolts-- 43 ft lbs
long bolts--46 ft lbs ,--
2nd step--turn all bolts 90 degrees.
cylinder head-bcqhgxcnnoqc5xlpx14pjgnh-5-0.jpg

Jul 03, 2018 | Chevrolet S 10 Cars & Trucks

1 Answer

Torq settings on 3.7 cyl heads


This is the info for the 2.8d CRDI 2008-11 engine code ENS (51C)

1 Replace Head Bolts
2 Stage 1 Tighten to15 Nm
3 Stage 2 Tighten to 30 Nm
4 Stage 3 Tighten to 85deg
5 Stage 4 Tighten to 85 deg
6 Stage 5 Tighten to 85 deg

Sequence

w93gwmwpatg0gaaaabjru5erkjggg==
If it is the 01-08 model 2.8 CRD engine code R2816K4 then it is this one
Stage 1 - Bolts 1 -18 = 30 Nm
Stage 2 - Bolts 1 -10 = 75 deg
Stage 3 - Bolts 11 - 18 = 50 deg
Stage 4 - Bolts 1 - 18 - 75 deg

Sequence
aa5xdif9xa+aaaaaaelftksuqmcc

If it is the Grand Cherokee then they fit 3.0 CRD, 4.7, 5.7 and the 6.1 SRT-8 engines. I can supply the details if needed. I hope that helps you.

Feb 04, 2015 | 2008 Jeep Cherokee 2.5

1 Answer

When you replace the head gasket on a kia do you also need to replace the bolts?


Most likely, many others with aluminum? heads have what are called "stretch" bolts, a one time use to maintain the correct tention and the torqe calibration on instalation.

Aug 06, 2013 | 2001 Kia Spectra

1 Answer

What is the torque of nissan urvan qr25 engine head bolts


nissan urvan 2006 engine head bolt torqe

Jan 31, 2012 | Cars & Trucks

1 Answer

HI HILUX SURF WITH 2LT DIESEL ENGINE CAN I GET CORRECT TORQE FOR. 1-TORQE FOR HEAD BOLT? 2-TORQE FOR CON ROD BEARING BOLT? 3-TORQE FOR MAIN BEARING BOLT?


Torque Settings Mains = 108NM
Big Ends = 54NM + 90° +90°
Flywheel = 122.5NM
Cylinder Head = 78 NM + 90° + 90°

Valve Settings
Exhaust = 0.40 mm - 0.50 mm
Intake = 0.20 - 0.3 0mm

Jun 30, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

I hav a 93 3100 efi v-6. i hav another engin that is out of a old's also. 90 to 93 or 94 i think. the blok's are almost the same. exaust ports on head's are difrint. and a couple ceincers. and oil pan. it...


this torques bit bolt is for secure the bracket of ac compreser and the dog bone and it srcew on the head bolt lower left side . make sure you have the crancksensor accest hole in block

Oct 22, 2010 | 1993 Oldsmobile Cutlass Supreme

1 Answer

What is torqe setting for toyta hiace head bolts and do i have to change bolts


LOOK IN THE OWNERS MANUAL IT SHOULD TELL YOU THE CORRECT TORQUE. AND YOU DONT HAVE TO CHANGE THE HEAD BOLTS BUT YES YOU SHOULD CHANGE THE HEAD BOLTS. IF YOU TAKE A PIECE OF WIRE AND CONTINUE TO HEAT IT UP, YOU WILL EVENTUALLY BREAK IT. THE SAME GOES FOR BOLTS. EVERY TIME YOU USE YOUR CAR THE HEAD BOLTS GET HOT AND EVERY TIME YOU TURN THE CAR OFF THEY GET COLD. THE METAL CHANGES.

Feb 23, 2010 | 1992 Toyota 4Runner

Not finding what you are looking for?
1997 Oldsmobile Achieva Logo

543 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...