At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
Remove the gearshift lever assembly from the control housing.
Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
Raise the vehicle and support it safely.
On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
Disconnect the speedometer from the transfer case/extension housing.
Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
Place a wood block on a service jack and position the jack under the engine oil pan.
On 4WD vehicles, remove the transfer case from the vehicle.
Remove the starter motor.
Position a transmission jack, under the transmission.
Remove the transmission-to-engine retaining bolts and washers.
Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
Lower the transmission jack and remove the transmission from the vehicle.
Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
Install the starter motor. Tighten the attaching nuts.
Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
On 4WD vehicles, install the transfer case.
On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
Connect the hydraulic clutch line and bleed the system.
Install the speedometer cable.
Check and adjust the fluid level.
Lower the vehicle.
Install the gearshift lever assembly. Install the boot cover and bolts.
Reconnect the negative battery cable.
Check for proper shifting and operation of the transmission.
GO TO MITCHELL ON DEMAND ON THE WEB OR THE DEALER. VEH IS TOO NEW FOR A HAYNES MANUAL. YOU MAY HAVE TO BUY THE FACTORY MANUAL, SO BRING YOUR VISA CARD.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
The rod bearing cap bolt torque specifications for the 3.0L V6 engine in a 2000 Ford Ranger XLT 4x4 with a manual transmission are as follows:
Step 1: Tighten the bolts to 15 foot-pounds of torque.
Step 2: Tighten the bolts to 30 foot-pounds of torque.
Step 3: Tighten the bolts an additional 90 degrees (1/4 turn) using a torque angle gauge.
It's important to follow the torque specifications and sequence in the manufacturer's service manual to ensure proper tightening and prevent damage to the engine.
u can get a manual for help..
I keep getting those for my vehicles too.. I know a lot of websites and which one is best for what type of vehicle. and which websites have customer care service etc free also
www.autozone.com and make a free account. Log on to that account. Put in the year make and model, look for the free repair guides. That is as close to free as you are going to get. The OEM manuals for motor vehicles are several hundred dollars.
Apr 23, 2002 - Mine takes 6 including 1 for the filter. This is what everything I've read says too. -------------- [font color="green"]1995 F-150 Supercab XLT ...
CarGurusJun 6, 2009 - 06 ford Ranger 4.0L v6- how much oil does it take? ... 3.75 qts if manual, 5.5 gal antifreeze capacity, 2.2 qt capacity in front and rear differential, ...Missing: 300 6cid
Your local dealer should be able to order one for you.
All Ford dealers get their owner's manuals from Helm. www.helm.com, I do
believe you have to be a dealer to order direct though.
×