Question about 2007 Mercedes-Benz ML350

2 Answers

Ml350 camshaft sensor problem - 2007 Mercedes-Benz ML350

Posted by tannourygeor on

Ad

2 Answers

Ossiess1

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Reset the computer after done changing

Posted on Jul 11, 2011

Ad

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 11 Answers

I think you need to post a little more information for someone to be of help. Cam Position Sensor and Crank Position Sensor problems are not uncommon on these cars (although you see more Crank Position Sensors go than Cam). Replacing them is not too difficult, if you have some mechanical skill. Just make sure your problem really is with the sensor before you start replacing parts. The sensors cost between $60 and $175 (depending on which and where you purchase it). If you have a specific code that you pulled from an ODB II reader, then start with that. If your check engine light is on, but you don't have an ODB II reader, then try your local parts store. Most will read codes for free.

Posted on Jan 30, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light code p0014 p0013


hi got 2012 mercedez benz c250 i change the camshaft actuators intake and exhaust. first thing i change becouse make a lot noise when'd is cool now i put the actuators the noise is gone for two days now i got the code poo14 now is jerking and shaking ???

Nov 20, 2013 | 2007 Mercedes-Benz ML350

2 Answers

Ml350 replaced a/b cam position sensor reset computer & and erra codes p0016/p0016 check engine ligth is reset car drives with light off when engine is turn off and started the light goes out if you...


P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

Nov 02, 2010 | Mercedes-Benz ML350 Cars & Trucks

1 Answer

Engine light for 2003 ML350 Benz


one of the engine sensors must be having a problem! have the vehicle diagonised! use a scan tool please

Jun 18, 2009 | 2007 Mercedes-Benz ML350

1 Answer

1993 ford taurus, replaced all starting and charging componets still no spark to plugs. Checked all fuses and all fusible links. Replaced key switch, ignition switch,neutral safty...


The camshaft position sensor sends a signal to the PCM, powertrain control module. The PCM then determines spark plug firing. Could be the camshaft position sensor.

1996 is all I have
Camshaft Position (CMP) Sensor 3.0L (2V) Engine
The camshaft position sensor (CMP sensor) (12126):
  • is a single Hall-effect magnetic switch activated by a single vane which is driven by the camshaft (6250).
  • provides camshaft position information which is used by the ignition coil (12029) and the powertrain control module (PCM) (12A650) for fuel synchronization.
3.0L (4V) Engine
The camshaft position sensor (CMP sensor) (6B288) is:
  • a variable reluctance sensor.
  • triggered by the high-point mark on the LH exhaust camshaft sprocket (6256).
-----------------
3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Then note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder block (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder block.
Installation
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be obtained prior to installation of the replacement camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs when arrow on locator tool is pointed approximately 75 degrees counterclockwise from the rear face of the cylinder block. This step will locate camshaft position sensor electrical connector in the pre-removal position.
  1. Roatate Syncro Positioning Tool T95T-12200-A clockwise slightly. This will engage oil pump intermediate shaft. Push downward while adjusting Syncro Positioning Tool T95T-12200-A until the Syncro Gear engages the camshaft gear.
  1. When synchronizer flange is fully seated against block, the installation tool should be facing counterclockwise of engine centerline approximately 33 to 45 degrees.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. sth~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (13-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.
824fa44.gif
Item Part Number Description 1 T95T-12200-A Syncro Positioning Tool 2 — Water Outlet (Part of Intake Assy) 3 9424 Intake Manifold 4 N602704-S Screw and Washer 5 12126 Camshaft Position Sensor 6 12A362 Synchronizer Assembly 7 12270 Hold-Down Clamp A — Tighten to 1.5-4 Nm (13-35 Lb-In) B — Tighten to 19-30 Nm (14-22 Lb-Ft)

Apr 04, 2009 | 1993 Ford Taurus

1 Answer

1997 mercury sable camshaft sensor replacement


do you have 3.L 2v or 4 valve?

3.0L (2V) Engine
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Syncro Positioning Tool T95T-12200-A
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Prior to removal of the camshaft position sensor (CMP sensor) (12126), set cylinder No.1 to zero degrees top dead center (TDC) of compression stroke. Note the position of the camshaft position sensor electrical connector. The installation procedure requires that the connector be located in the same position.
Removal
  1. Disconnect battery ground cable. Refer to Section 14-01 .
  1. Disconnect engine control sensor wiring connector from camshaft position sensor.
  1. Remove camshaft position sensor retaining screws and camshaft position sensor from camshaft position sensor housing.
  1. If removing camshaft position sensor housing from the cylinder blocks (6010), proceed with Removal Step 5. If not removing camshaft position sensor housing, proceed to installation Step 6.
  1. Remove hold-down clamp (12270) (bolt and washer assembly).
  1. Remove camshaft position sensor housing from cylinder blocks.
Installation
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: A special service tool such as Syncro Positioning Tool T95T-12200-A must be used to position the synchronizer assembly prior to installation of the camshaft position sensor. Failure to follow this procedure will result in improper camshaft position sensor alignment. This will result in the fuel system being out of time with the engine, possibly causing engine damage.
    Attach Syncro Positioning Tool T95T-12200-A as follows:
    1. Engage camshaft position sensor housing vane into the radial slot of the tool.
    1. Rotate tool on camshaft position sensor housing until tool boss engages notch in camshaft position sensor housing.
  1. Pre-lubricate synchronizer gear with engine oil meeting Ford specification ESE-M2C123-A prior to assembly.
  1. Install camshaft position sensor housing so that drive gear engagement occurs. Locate camshaft position sensor electrical connector in the pre-removal position.
  1. Install hold-down clamp (washer and bolt) and tighten bolt to 19-30 Nm (14-22 lb-ft).
  1. Remove Syncro Positioning Tool T95T-12200-A.
  1. svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If camshaft position sensor electrical connector is not positioned properly, DO NOT reposition the connector by rotating the camshaft position sensor housing. This will result in the fuel system being out of time with the engine, possibly causing engine damage. Remove the camshaft position sensor housing and repeat installation procedure, beginning with Step 1.
    Install camshaft position sensor and retaining screws. Tighten screws to 1.5-4.0 Nm (14-35 lb-in).
  1. Connect engine control sensor wiring connector to camshaft position sensor.
  1. Connect battery ground cable.

Feb 22, 2009 | 1997 Mercury Sable

Not finding what you are looking for?
2007 Mercedes-Benz ML350 Logo

1,214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

jalal

Level 2 Expert

178 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...