Question about 1999 Volvo S70
Rocker Arm (Valve) Cover
REMOVAL & INSTALLATION
2.3L 4-Cylinder Engines
Use a roller or your finger to spread sealant, do not use an excessive amount of sealant, or the oil passages could become clogged.
Fig. 3: Remove the spark plug cover and the plug wires or ignition coils to access the retaivalve cover gasket, how to - 90953p80.jpg
valve cover gasket, how to - 90953p72.jpg Remove the retaining bolts
Fig. 5: A light tap wivalve cover gasket, how to - 90953p81.jpgced hammer is usually required to loosen the valve cover
Fig. 6: Carefully lift the upper cvalve cover gasket, how to - 90953p82.jpg up and off the lower section. Note the integral camshaft bearing caps in the casting
Posted on Jan 29, 2011
How to remove valve cover on 08 chevy impala 3.5
Posted on May 08, 2013
SOURCE: valve cover gasket leaking
When you buy the valve cover set, it will include the spark plug well "O" rings. Simply remove the valve cover and on the underside of the valve cover, you'll see the "O" rings that need replaced and you'll see exactly how the valve cover gasket itself fits.
Posted on Feb 12, 2009
You need an aftermarket serviice manual from Haynes or Chilton.
They will have that kind of info.
I know of no car (I don't know them all) where that is needed and depending on the cover material (sheet steel or cast), could lead to warping and new leaks. I always use a thin film of silicone whether it is specified or not and there are torque specs for ALL valve covers I have ever seen.
Posted on Sep 13, 2008
I don't have experience with this engine but guess you won't have to remove it for valve cover gasket work but perhaps can lift it a bit [not by hand!] after loosening engine mounts.
Posted on Nov 18, 2008
ALL DATA time to R&R valve cover gaskets both sides is 2.1 hours. you will need to remove brackets and connectors on either side, It will also help to take the upper plenium bolts out but not completly pull the plenium. If you don't have a lot of mechanical experiance and some basic tools. you may want to consider to have a local a shop to perform this service for you after you get a estimate. RON.
Posted on Jan 18, 2009
The first step is to remove all the parts that are in the way of you being able to remove the valve covers. (Ex.: air intake, loose wires etc.) Then you will need to remove your valve covers (using basic tools) and be very careful to not let anything get on your lifters, which your valve covers protect. Once you have the valve covers off compare the new gaskets to make sure they are the right size. Then remove the old gasket and replace with the new one using a high temp gasket sealant (available at any auto parts store) to attach the gasket to the valve covers. Then tighten down snug and check for leaks after replaced.
Posted on May 06, 2009
Tips for a great answer:
Oct 12, 2014 | 1999 Chrysler Town & Country
on Mar 10, 2010 | Jaguar XJ8 Cars & Trucks
Jan 13, 2014 | 2006 BMW 750Li
Nov 23, 2012 | 2006 Subaru Forester
May 27, 2010 | 1991 Buick Century
May 23, 2009 | 1987 Ford Bronco
May 05, 2009 | Chevrolet Malibu Cars & Trucks
Feb 12, 2009 | 2001 Nissan Altima
May 17, 2008 | 1992 Volkswagen Jetta
Jul 24, 2016 | 1999 Volvo S70
1,839 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: