Question about 2000 Chevrolet Silverado 1500

2 Answers

I have a 2000 chevy silverado 4X4 1500. I have replaced 2 starters becaule the short bolt side support is broken. what can cause this

Posted by kellybh01 on

Ad

2 Answers

Bob Nunya

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

That was a common problem with the long/short bolt starters. The solution is the newer style starter with the 2 long bolts. I just replaced mine today. It already has the 2 long bolt style unit, but the new one came with a long bolt for those doing the conversion.

Posted on Jan 07, 2012

Ad

Chris Ward

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 731 Answers

Did you use the Shim's that come with new starters or check the gap with the little rod that come with the starterto see if the shim's are needed.

Posted on Jan 30, 2011

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuse box 2000 Chevy silverado


there are like 3 for a 2000 chevy silverado. 1 on left side of dash accessible only when door is open. 2 on right side of dash, not sure those fuses are applicable to you tho, and 3 under hood beneath a plastic cover that you snap off by pulling on.

May 13, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

Starter mount


the problem will be finding a housing to fit correctly and make contact with the flywheel when you try to start the vehicle.

May 23, 2012 | Cars & Trucks

1 Answer

I'm trying to remove my oil pan on a 2000 Silverado 1500 with a 4.3L V6. I've removed all of the bolts, the starter, the transmission cooling lines, the oil level sensor bracket, the front wire bracket,...


I am not sure, But there could be six more bolts to remove. They will be on the side of the pan, about half way up. three on each side. Sorry for guessing, I work on to many makes and models. Also the gaskets do hold the pan on tight sometimes. If there are no extra bolts then carefully pry it off.

Feb 28, 2011 | 2000 Chevrolet Silverado 1500

1 Answer

How do I take off a starter on a 2000 Chevy S-10?


Disconnect battery cable Ground side, Raise vehical and place jackstands to stabelise, Crawl under vehicals passenger side, remove the 2 bolts on the nose of the starter, and brace on the rear of case if equipped. Push back starter and lower nose first, remove wire retaing nuts, and reverse to reinstall

Jun 11, 2010 | 2000 Chevrolet S-10

1 Answer

2000 Chevy Silverado 2500 6.0 litre fuel pump


lifting the truck bed off the frame works best if you dont have a lift..take the fuel neck loose from bed and remove bolts holding bed to frame from the drivers side..loosen the bolts on passenger side..raise the bed on drivers side while watching bumper to bed clearance on passenger side.. you should get enough clearance to remove fuel pump from tank

Dec 26, 2009 | 2000 Chevrolet Silverado

2 Answers

How do I replace the starter on my 1993 chevy?


Disconnect the negative cable from the battery..
Under the front end - find the starter near where the trani connects to the motor and the really big gear (flywheel) is..
Undo 2 bolts to remove the starter.. take the wires off and be sure to put the wires on the starter the same way..
Connect the wires to the new starter and put the starter in with the to bolts.. The starter will only go in one way so you cant mess up how it goes in..

Good luck !

Sep 23, 2009 | 1993 Chevrolet K1500

1 Answer

I need to replace my starter in my 2000 Chevy Blazer. I need help please.


Unhook battery cables from battery locate starter on underside of engine block on the passenger side three bolts to take out replace starter and reverse procedure fairly easy job!! good luck.

Aug 05, 2009 | 2000 Chevrolet Blazer

1 Answer

Diagram needed


you really don't need one.....
1.Disconnect the battery
2.locate the starter. If its a v8 itll be on the driver side at the back of the engine beside the oil pan
3.there are two bolts on the bottom of the starter that you need to remove with a 9/16 socket or wrench.(support the starter when you remove the last bolt so the wires don't get broken)
4.observe the location of all of the wires attached to the starter(make a diagram so you don't forget where they go)
5.Remove the nuts that hold the wires on the starter.(make sure the ring connectors and wires are in good shape if you notice any damaged ones they should be replaced)
6. reverse procedure to install new one
..............hope this is helpfull.good luck!

Dec 10, 2008 | 1995 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

john h

Level 3 Expert

23515 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...