Question about Jeep Grand Cherokee

1 Answer

Miss fires and stots off when I give it gas as codes 1391 ,0351, 0352, 0353,

Posted by henrywolf on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 329 Answers

P1391 - Not a valid obd code.
B1391 - Oil Level Switch Circuit Failure
C1391 - Not a valid obd code.
U1391 - Not a valid obd code.
Its possible you may have misread this code. If it is B1391 that would be the only code with 1391 for your vehicle.

P0351 - Ignition Coil A Primary / Secondary Circuit Malfunction. The ignition signal from the Powertrain Control Module or Electronic Control Module is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

Possible Causes:
- Open or short in the ignition coil circuit
- Ignition coil circuit shorted to ground
- Ignition coil connector
- Damaged ignition coil
- Damaged PCM

P0352 - Ignition Coil B Primary / Secondary Circuit Malfunction.
Same repair info as P0351.

P0353 - Ignition Coil C Primary / Secondary Circuit Malfunction.
Same repair info as P0351

- If damage, repair ignition coil circuit
- Replaced ignition coil
- Replaced

Posted on Jan 16, 2011


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:


What could cause eng to stubble/rough running mostly when giving gas?

I have no idea what kind of car or truck you have but have you checked fuel pressure and/or volume?

Got a 2004 that sounds like its missing and it also loses power when taking off and is using so much gas . Any suggestions why its doing this and can i do for it using so much gas

not knowing what kind of car doesnot help, but if it sounds like its missing, and loses power on taking off ,plus burn alot of fuel , i guessing that it has a miss fire, i would bet that the service engine light on the dash is on, of blinking . if it is on acode reader will give you what cly. is missing. and that can be anything from a spark plug to a coil. fuel injector, with out know if and what the codes are not much help.

2003 Santa Fe V 6 miss firing with New plugs and wires

Got a check engine light? Get the codes read to find out if the misfires are on all cylinders or just 1. Could be ign coil, bad crank or cam sensor, or a valve issue

When i come to a stop, my car doesn't want to accelerate. I give it gas and it barely starts moving, almost like the transmission is slipping. It has an automatic transmission, if I ride the gas pedal...

evap codes won`t cause the acceleration problem.the miss fire codes could cause this if the miss fire is bad enough repair the miss fire problem first.i assume that you have checked the trany fluid for level and condition.if this happens all the time from a stop then you could have a transmission problem with 1st gear activating from a stop.if the rpm`s rise and your not moving with the rpm increase then its a transmission problem.the evap codes will have to be cleared then the car driven to see what shows up again as some false codes can set other codes.


if check engine light is on. take it to an auto parts store and they will read the problem code for free. auto-zone etc, no sense in spending money if you do not have too for the wrong part. have a good day !

Engine missing --started missing all of a sudden . replaced plugs and cam sensor in dist.. Roter and dist. cap and wires in good shape. Had a test on the engine, said that it was miss fireing at several...

On my 2002 safari I had a inter miss fire. After double checking all electrical. I had a bad injector of all things that was bad. My not be ur case but I thought I would mention it

Check engine light has come on and engine is stalling.

sounds like a eng miss fire eng lite on OBD 2 scaner tool to retreve code don't GUE$$ the problem
Not finding what you are looking for?

Open Questions:


Jeep 2001 jeep grand cherokee v8 4x4 Laredo code p1686 code showing up... So originally when the Jeep broke down I had to send in the main computer to be swiped to bypass the security system. I don't remember what security code that was Prior but now I've shipped out the computer and received it back and re-install it into the Jeep that original code no longer is showing up but now when I try to start it, it still does the same thing it'll start for about 5 seconds and then turn right off. I did the Diagnostics and receive the code p1686 so I'm confused at this point? I thought that sending in the main computer was supposed to bypass the whole security system. So now why is p1686 coming up if this is wiped and bypassed? Does the immobilizer and key all need to still be matched up to the immobilizer and be the same because I had some extra immobilizers that weren't matched to the keys and I'm not sure which is original because thru all of this I didn't know at the beging how security systems worked, but now i know a little and know that it takes a few different components to match up and read each other to all work as one to make it start and stay running. Is that possibly the issue? And bypassing the computer is that different than the immobilizer and the key matching because I thought they all work together, and sending in the main ecu to be wiped was going to bypass all of this.... Also security light the onewith the key and the line through it WAS ON NOW IS OFF AFTER REINSTALLING THE ECU.I'm sorry if this is confusing I'm not a mechanic myself I'm just trying to get this figured out because it's been a long time and my car has been down for about 2 months now at this point and money a little tight with a newborn being a single mommy...thank you.

Cars & Trucks Logo

Related Topics:


Ask a Question

Usually answered in minutes!

Top Jeep Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6929 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers


Level 3 Expert

4377 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides