Question about Lincoln Town Car

1 Answer

1996 lincoln town car signature series. ok so changed the power steering pump, changed the steering gearbox, everything is new except the shaft leaving the firewall from the steering column, and the steering column, when turning the wheel its very tight and jerky in some spots what may be causing this the steering column or the u joint outside the firewall. im lost and i really dont want to change the steering column unless i have to. thanks

Posted by hoz_photogra on

Ad

1 Answer

Bill Boyd

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 53,816 Answers

When you replaced the steering box did you check the position of the "u' joints to each other
it that is not correct , it will be lumpy to turn

Posted on Jun 28, 2017

Ad

5 Related Answers

Anonymous

  • 76 Answers

SOURCE: atv cv joint boot

lubricate boot. then tighten, using a new clamp, try using lock thread on bolt. hope this helps

Posted on Nov 01, 2008

Ad
chuck943

Chuck Martin

  • 783 Answers

SOURCE: changing turn signal switch 1986 lincoln town car.

No just remove the bottom cover then you should be able to push the upper cover up enough to clear so you can get to the 2 screws in the switch then remove and disconnect the connectors.
If you can not get enough clearance with the upper cover on then you will have to remove the ignition lock cylinder to remove the upper cover. To remove lock cylinder just turn to on position then look under the lock cylinder on the steering column and you will see a small hole,take a pick or small screw driver and stick it into hole to push button on lock cylinder then pull it out.

Posted on Feb 24, 2009

Flat48

Arther Scott

  • 77 Answers

SOURCE: Need to have diagram for fuses in 1989 Lincoln

Go to the link below and you will see the diagram for the fuse panel in your car. You can click on the picture to enlarge it as well.

http://www.repairpath.com/rp.asp

Posted on May 22, 2009

Anonymous

  • 34 Answers

SOURCE: 1997 SIGNATURE LINCOLN TOWN CAR, THE RESET SWITCH FOR FUILPUMP

The inertia switch should be located in the trunk, on the right-hand side, behind the feltlike trim material.

Posted on Jul 09, 2009

Anonymous

  • 1 Answer

SOURCE: Instructions for built in garage door opener on

how do i program a garage door opener on a 06 mercury mountaineer

Posted on Nov 21, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2008 Lincoln Navigator with stiff steering. I have replaced power steering pump and rack and pinion.


There's this website www.reliable-store.com
They have books on ALL vehicles.
it covers wiring diagrams, electrical diagrams,
fuse diagram, torque specs, PCV, error codes, fault codes, service info, repair info, parts info, troubleshooting owner's/service/repair/
parts/maintenance manuals etc everything totally..
I have 1987 toyota 4runner model and I keep servicing and when needed repair it on my own. worth it !!!

Mar 17, 2018 | Lincoln Cars & Trucks

1 Answer

How to remove and replace heater core on a 1996 lincoln town car, signature series


Hate to tell you this, but you will need to remove the entire dashboard to access the heater core.

Jan 03, 2015 | 1996 Lincoln Town Car

1 Answer

How to replace a pitman arm seal on a lincoln town car signature series


I have not had much luck replacing seals on those.. the pitman shaft gets a score line in it and starts leaking even with a new seal in a short time. Try finding a used steering box for it and check for signs of a leak before you put it on.. You will save yourself some frustration in the long run.

Jul 28, 2010 | 1994 Lincoln Town Car

2 Answers

Lincon Town Car Interchangeable Parts


what other year than a 1994 will fit on a 1994 lincoln towncar

May 12, 2010 | 1994 Honda Accord

1 Answer

Noise in steering of 1996 lincoln towncar


Start by checking power steering fluid then see if noise is coming from power steering pump. listen in area of power steering pump while someone turns steering wheel for you.

Aug 30, 2009 | 1995 Lincoln Town Car

2 Answers

1997 SIGNATURE LINCOLN TOWN CAR, THE RESET SWITCH FOR FUILPUMP


The inertia switch should be located in the trunk, on the right-hand side, behind the feltlike trim material.

Jul 09, 2009 | 1996 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...