2006 Toyota 4runner sport 4.0L V6 2wd bottoms out too easy on front.

Question edited for clarity.
Question moved to model category.

2006 Toyota tundra 4.7L Front End Torque Specs

toyota-specs.com https://toyota-specs.com > cars > 2006 > tundra4.7 > t...
Toyota Tundra Front Axle Nut Torque Spec : 203 ft-lbs · Toyota Tundra Wheel Hub Torque Spec : 100 ft-lbs ...

BHA53102 Axle / Spindle Nut Torque Specification

1A Auto https://docs.1aauto.com > BHA53102 Torque S... PDF Toyota. 4Runner. 1996-02 4 Wheel Drive. Front. 174. 236. Toyota. Sequoia ... Tacoma. 2001-04 4 Wheel Drive. Front. 173. 235. Toyota. Tundra. 2000-06 4 Wheel ...
1 page
https://www.google.com/search?q=2006+Toyota+Tundra+4x4+front+axle+torque

..

not that easy to get that info
try ebay for the ECU
also for a Toyota 4Runner complete factory workshop manual

might try join a free 4runner owners forum or face book group

There is nothing to adjust on the rear because it is a solid axle, most dealers and alignment shops do a 4wheel alignment anyway and they don't charge less for a two wheel alignment. A 4wheel alignment also reveals any possible bent suspension components or frame misalignment..

The rear window washer gets its feed from the front reservoir. One reservoir feeds both windows.

You have to crawl under the car to get this done. Identify the location of the bulb then crawl underneath and locate the appropriate connector. Grab the connector with your hand and twist the connector right-to-left. The connector will then disengage from the plastic housing and you can withdraw the connector and the bulb from the housing. Once disconnected, grab the bulb with one hand and the connector with the other, and pull out the bulb straight out (no twisting). Replace is the reverse. Easy. Should take less than 1 minute.

2006 TOYOTA 4RUNNER - V6 4.0L 3956cc GAS FI N 1GRFE
Belt Routing Diagram - Multiple Accessory, w/A.C.



From DAYCO Products Catalog

Hope help with this (remember rated this post). Good luck.

MAKE SURE YOUR TRIP COUNTER IS ON MILES. WITH CAR OFF PRESS TRIP RESET AND HOLD IT IN. TURN KEY TO POWER POSTION WITHCOUT TURNING CAR ON. YOU WILL SEE LINES THAT BLINK AND GO OUT. THEN A BUNCH OF ZEROS. THE YOUR MILES AGAIN.. AT THAT POINT ITS RESET

Blown bulbs , easy!.
Remove the shroud under the steering column , ( the one where the fuse box and bonnet release is situated)
This will give you access to the bottom screws of the binacle around the speedo ( other screws up from underneath above the speedo)
Once binacle removed you will see the screws holding the speedo in, remove them and ( with the steering tilted fully down) remove the speedo head, there should be 3 or 4 electrical plugs in the back of the speedo ( don't worry they only fit one way and can't be muddled up )
In the back of the speedo are twist clips retaining the bulbs, remove and replace blown bulbs.
Reverse procedure to reinstall speedo.
A magnetic phillips head screwdriver is handy to get the screws back in without loosing them into the back of the dashboard.

there should be a small tube where you can fit the lug nut wrench and use it to crank it down

Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


Remove or disconnect the following:

Front turn signal lamp

Connector

2 screws

2 claw fittings

Fog lamp assembly

Fog lamp bulb as shown

Fog light unit

To Install

1. Install or connect the following:
   • Fog light unit
   • Fog lamp bulb as shown
   • Fog lamp assembly latch the 2 claw fittings and 2 screws
   • Connector
   • Front turn signal lamp

Trying to post the pics now....