Rear differential oil leak

Rear cover gasket is easy. Unbolt, drain, clean and replace gasket; fill with proper gear oil. Pinion seal on the front of the differential, different matter. If its the pinion seal leaking, take it to a shop with experienced techs.

what about it?

conventional axle or limited slip? Get axle code off door sticker.

SECTION 205-02: Rear Drive Axle/Differential - Ford 8.8-Inch Ring Gear 1998 Explorer/Mountaineer Workshop Manual
IN-VEHICLE REPAIR Rear Wheel Bearing and Axle Shaft Oil Seal -4.0L SOHC and 4.0L EI, Conventional
Special Tool(s) Axle Seal Replacer
T83T-1175-A Axle Wheel Bearing Puller
T83T-1225-A Axle Wheel Bearing Replacer
T83T-1225-B Driver Handle
T80T-4000-W Impact Slide Hammer
T50T-100-A
Removal

1. Remove the axle shaft; refer to Axle Shaft in this section.

Axle Shaft Removal

1. CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
   Loosen the lug nuts (1012).
   1. Remove the center cap.
   1. With the weight of the vehicle on the wheels, loosen the lug nuts.

1. Raise and support the vehicle.

1. Remove the wheel and tire assembly.
   1. Remove the lug nuts.
   1. Remove the wheel and tire assembly.

1. Remove the axle housing cover (4033).
   1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
   1. Remove the axle housing cover bolts.
   1. Remove the axle housing cover.

1. Remove the rear disc brake rotors (2C026); refer to Section 206-04 .

1. CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
   Remove the U-washers (4N237).
   1. Push the axle shafts inboard.
   1. Remove the U-washers.

1. Reinstall the differential pinion shaft.
   1. Install the differential pinion shaft.
   1. Install the differential pinion shaft lock bolt finger-tight.

1. CAUTION: Do not damage the inner wheel bearing oil seal (1177).
   Remove the two axle shafts.

Installation

1. Lubricate the lip of the inner wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.

1. CAUTION: Do not damage the inner wheel bearing oil seal.
   Install the two axle shafts.

1. CAUTION: Do not damage the rubber O-rings in the U-washer grooves.
   Install the U-washers.
   1. Position the two U-washers on the button end of the axle shafts.
   1. Pull the axle shafts outward.

1. Install the differential pinion shaft.
   1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
   1. Install the differential pinion shaft lock bolt.

1. Install the rear disc brake rotors; refer to Section 206-04 .

1. Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant; refer to Axle Housing Cover in this section.

1. WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control.
   Clean the wheel hub and mounting surfaces.

1. Install the tire and wheel assembly.
   1. Position the tire and wheel assembly.
   1. Install the lug nuts and lower the vehicle.
   1. Tighten the lug nuts.
   1. Install the center cap.

1. CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time.
   NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris.
   Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.

Installation

1. Lubricate the new rear wheel bearing.
   1. Use Thermally Stable Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.

1. Use Axle Wheel Bearing Replacer with Driver Handle to install the rear wheel bearing.

1. Lubricate the lip of the new axle shaft oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Use Axle Seal Replacer with Driver Handle to install the axle shaft oil seal.

1. Install the axle shaft; refer to Axle Shaft in this section.

Axle Vent
NOTE: If the vent cannot be cleared, it must be installed new.
A plugged vent will cause excessive seal lip wear due to internal pressure buildup. If a leak occurs, check the vent. Make sure the vent hose is not kinked. Remove the hose from the vent nipple and clear the hose of any foreign material. While the hose is removed, pass a length of mechanics wire or a small diameter Allen wrench in and out of the vent to clean it. Connect the hose when done. The vent is located on the drivers side top of axle housing.
If you plan on doing most repairs yourself I would suggest buying a Haynes or Chilton manual for your particular vehicle. Or there are some data disks on e.bay($12-$15) For a cost of under $25, you can almost do any repair yourself with these manuals.Also there are online manuals like the site called ALLDATA where guides can be viewed for a fee. All these solutions will save you time and money, and give peace of mind over correct repairs. I can post you some procedures here also.

1. CAUTION: Do not use heat to loosen a seized lug nut. Heat can damage the wheel (1007) and the rear wheel bearings (1225).
2. Loosen the lug nuts (1012).
3. Remove the center cap.
4. With the weight of the vehicle on the wheels, loosen the lug nuts Raise and support the vehicle. .Remove the wheel and tire assembly.
   
5. Remove the lug nuts.
   
6. Remove the wheel and tire assembly. Remove the axle housing cover (4033).
   
   1. Loosen the axle housing cover bolts (4346) and drain the rear axle (4001).
   1. Remove the axle housing cover bolts.
   1. Remove the axle housing cover.
   

7.Remove the rear disc brake rotors You will have to remove the brake caliper to get rotor off.
8. CAUTION: Once the differential pinion shaft (4211) has been removed, turning the differential case (4204) or an axle shaft (4234) will cause the differential pinion gears (4215) to fall out of the assembly. This could result in chipped or damaged components.
9.
1.Remove the differential pinion shaft lock bolt. 2.Remove the differential pinion shaft. 10.CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Remove the U-washers (4N237).

1. Push the axle shafts inboard.
2. Remove the U-washers.

11.Reinstall the differential pinion shaft.
1. Install the differential pinion shaft.
1. Install the differential pinion shaft lock bolt finger-tight.

12.CAUTION: Do not damage the inner wheel bearing oil seal (1177). Remove the two axle shafts.

CAUTION: Never remove the axle shaft oil seal by itself. Always remove the rear wheel bearing and the axle shaft oil seal at the same time. NOTE: If the axle shaft oil seal is leaking, the axle housing vent may be plugged with debris. Use Impact Slide Hammer and Axle Wheel Bearing Puller to remove the rear wheel bearing and the axle shaft oil seal.

Axle bearing puller end..
Installation
Lubricate the lip of the inner wheel bearing oil seal.
Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. CAUTION: Once the differential pinion shaft has been removed, turning the differential case or an axle shaft will cause the differential pinion gears to fall out of the assembly. This could result in chipped or damaged components.
2. Remove the differential pinion shaft.
3. Remove the differential pinion shaft lock bolt.
4. Remove the differential pinion shaft.

CAUTION: Do not damage the inner wheel bearing oil seal. Install the two axle shafts. CAUTION: Do not damage the rubber O-rings in the U-washer grooves. Install the U-washers.
1. Position the two U-washers on the button end of the axle shafts.
1. Pull the axle shafts outward.

Install the differential pinion shaft.
1. Align the hole in the differential pinion shaft with the differential pinion shaft lock bolt hole.
1. Install the differential pinion shaft lock bolt.

Install the rear disc brake rotors; Install the axle housing cover and fill the rear axle housing (4010) with 2.4 liters (5.5 pints) of specified lubricant
WARNING: Always remove any corrosion, dirt or foreign material that may be present on the mounting surfaces of the wheel or the surface of the wheel hub or rear disc brake rotor that contacts the wheel. Installing wheels without proper metal-to-metal contact at the wheel mounting surfaces can cause the lug nut to loosen and the wheel to come off while the vehicle is in motion, causing loss of control. Clean the wheel hub and mounting surfaces. Install the tire and wheel assembly.
Position the tire and wheel assembly. Install the lug nuts and lower the vehicle. Tighten the lug nuts. Install the center cap. WHEW Hope this can help you

2000 TOYOTA TACOMA 2.7L 4-cyl Engine Code 3RZ-FE

Engine Oil Grade 1......API* All TEMPS......5W-30 Optional ..10W-30
Engine, 2WD, with filter..........5.5 liters
Engine, 4WD, with filter..........5.4 liters

Manual Transmission,......GL-5/ GL-4 All TEMPS......75W-90
Automatic Transmission,A340E......AF3 / A43D......AF3

Differential, Front/ Rear W/ ADRD......GL-5 ALL TEMPS......75W-90
Differential, Front Less ADRD......GL-5 ALL TEMPS......80W-90

Transfer Case,......GL-4/GL-5 ALL TEMPS......75W-90 Gear oil.

Capacity:
Cooling System, Initial Fill..........8.5 liters
Automatic Transmission, A340E Initial Fill..........1.6 liters
Automatic Transmission, A340F Initial Fill..........2 liters
Automatic Transmission, A43D Initial Fill..........2.4 liters
Automatic Transmission, Total Fill
4 speed A340E..........7.2 liters
4 speed A340F..........10.1 liters
4 speed A43D..........6.5 liters
Manual Transmission, ..........2.5 liters
Differential, With ADRD Front..........1.2 liters
Differential, Without ADRD Front..........1.1 liters
Differential, 2WD V6 Rear..........2.6 liters
Differential, 4WD Extra Long Rear..........2.5 liters
Differential, Short WB With LSD Rear..........2.7 liters
Differential, Short WB Without LS Rear..........2.6 liters
Transfer Case, Electronic..........1.2 liters
Transfer Case, STD..........1 liters

PINION FLANGE & OIL SEAL

CAUTION: Following procedure must be used to retain proper pinion bearing preload. Failure to follow procedure may result in premature axle assembly or component failure. Ensure pinion bearing preload is checked before disassembly, as previous pinion bearing preload will be used during reassembly.

Removal

1. Raise and support vehicle. Scribe reference mark on drive shaft-to-pinion flange on differential for reassembly reference. Remove bolts and "U" joint straps at pinion flange on differential.
Disconnect drive shaft from differential.
2. Remove rear wheels and brake drums to prevent any drag that may affect pinion bearing preload reading. Using INCH-lb. torque wrench, measure amount of force required to rotate pinion. This is pinion bearing preload. Record pinion bearing preload for reassembly reference.
3. Using Holder (6719), hold pinion flange. Remove pinion nut and washer. Scribe reference mark on pinion flange-to-pinion for reassembly reference. Using appropriate puller, remove pinion flange from pinion. Remove oil seal from axle housing.

Installation

1. Ensure oil seal surface in axle housing is clean. Coat lip of oil seal with gear lube. Install oil seal using appropriate seal installer. Drive oil seal into axle housing until oil seal installer contacts axle housing.
2. Install pinion flange on pinion with reference mark aligned. Using appropriate pinion flange installer, install pinion flange on pinion.

CAUTION: Washer must be installed on pinion with convex side of washer facing outward (away from pinion).

3. Install washer on pinion with convex side of washer facing outward (away from pinion). Install NEW pinion nut. Tighten pinion nut to 210 ft. lbs. (285 N.m). Rotate pinion several times to seat pinion bearings.

CAUTION: DO NOT overtighten or loosen then retighten pinion nut when adjusting pinion bearing preload. If pinion nut is overtightened, collapsible spacer on pinion must be replaced.

4. Rotate pinion using INCH-lb. torque wrench. Rotating torque should be equal to reading recorded in removal step 2) , plus 5 INCH lbs. (.056 N.m). If rotating torque is low, tighten pinion nut in small increments until proper rotating torque is obtained.
5. To install remaining components, reverse removal procedure using NEW "U" joint straps and bolts. Ensure all reference marks are aligned. Tighten bolts to specification. Check lubricant level and add if necessary.

Is the front pinion seal leaking any oil? if so replace seal. If not drain oil out of differential and reseal and add oil back.

It should be listed in the owners manual, but because of different oil cooler setups you may have to do the change yourself and add oil until the correct level is established..... for the first oil change.
Most likely 7 liters,but start with 5,run the engine to fill the oil filter,let it sit for 5 mins and recheck and fill to full.
Note the amount needed for next time.

Block the front tires. Break the rear lugs loose. Jack up the rear of the truck at the center if possible. remove the wheels & brake drums. Remove the brake shoes,return springs & all the other hardware. Remove the differential cover & drain oil. If you have a posi the next step sucks. You need to remove the threaded pin from the housing & remove the axle retaining clips. All the while,being carefull of the spring in the posi unit. If no posi,then same procedure,minus the "pucker factor". After the axle is out,take a large flat blade screw driver or pry bar & pop the seal out. Keep in mind the axle bearing is probably gone too , so that's another procedure. Keep it apart,you'll be glad you did.

No. This is a cheap repair even if you take to Chrysler or any repair facility. All they do is drop the drive line and remove the pinion nut and remove the seal and tap the new one into place. Should only take them about an hour at most to do this.

Axle Shaft Removal

1. Raise and support the vehicle. For additional information, refer to Section 100-02 .

1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .

1. Remove the differential housing cover (4033).
   1. Loosen the bolts and drain the lubricant from the rear axle housing (4010).
   1. Remove the bolts.
   1. Remove the differential housing cover.

Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .

1. CAUTION: Turning the differential case (4204) or an axle shaft (4234) with the differential pinion shaft (4211) removed will cause the differential pinion gears (4215) to fall out of the assembly and damage the components.
   Remove the differential pinion shaft.
   1. Remove the differential pinion shaft lock bolt.
   1. Remove the differential pinion shaft.
2. CAUTION: Do not damage the rubber O-ring in the U-washer groove.
3. Remove the U-washer (4N237).
4. Push the axle shaft inboard.
5. Remove the U-washer.

Reinstall the differential pinion shaft.

1. Install the differential pinion shaft.
2. Install the differential pinion shaft lock bolt finger-tight.
3. CAUTION: Do not damage the wheel bearing oil seal (1177).
   Remove the axle shaft.

-----------------------------------------------------------------------------------------------------------------
Seal Removal

1. Remove the axle shaft (4334). For additional information, refer to Axle Shaft in this section.

1. CAUTION: Never remove the wheel bearing oil seal (1177) by itself. Always remove the rear wheel bearing (1225) and the inner wheel bearing oil seal at the same time.
   NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged with foreign material.
   Using the special tools, remove the rear wheel bearing and wheel bearing oil seal together.

Installation

1. Lubricate the new rear wheel bearing.
   • For 4.0L SOHC and 4.0L EI with limited slip rear axles and 5.0L vehicles, use SAE 75W-140 High Performance Rear Axle Lubricant F1TZ-19580-B or equivalent meeting Ford specification WSL-M2C192-A.
   • For 4.0L SOHC and 4.0L EI with conventional rear axles, use SAE 80W-90 Premium Rear Axle Lubricant XY-80W90-QL or equivalent meeting Ford specification WSP-M2C197-A.

1. Using the special tools, install the rear wheel bearing.

1. Lubricate the lip of the new wheel bearing oil seal.
   • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.

1. Using the special tools, install the wheel bearing oil seal.

1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.