Need wiring diagram for 1994 dodge van 250 with 5.2 liter motor. please show from distibutor cat top to spark plugs.@

So what you need to do is type in photos of a 1984 Dodge ram van spark plug and then look at the photos because i cant send a pic on here.

Hi there:
Check this for 1994 Cadillac Eldorado Touring 4.6 liter DOHC V-8 VIN "9"and Eldorado 4.6 liter DOHC V-8 VIN "Y"




Or, check this diagram for 1994 Cadillac Eldorado Touring 5.7 liter V-8 VIN "P"



Hope this helps.

Carefully confirm first, that when you installed your new plugs that you also installed the plug wires to the correct plug.

If you've had to swap any of the wires around, start up the van to check for improvement.

Please let me know if you have any questions, and thanks for using Fixya.

2.5 liter



3.0 liter



3.3 liter:

Here is the firing order for the 1994 Chevrolet Lumina APV Van with a 3.1 Liter engine with a distributor, and the 3.8 liter engine had the coil packs, and let me know if you need any help to understand this diagram, or if you require any further assistance.

Firing Order 1-6-5-4-3-2 you need to ffind # 1 cylinder pull spark plug take distibutor cap off and torm motor over with yor finger in the plug hole you will hear a poof thats TDC AND look at the distibutor now its pointing to the wire that goes to that plug.. you don't vn ned a fing ord jus lots o time to do it only 5 cylindes, THE 6TH ONE IS MY FREE GIFT TO YOU.. NOT QUITE RIGHT ? YOU CAN MOVE THE WIRES AHEAD 1 ON THE CAP OR BACK 1 .. I TEEMS TO ME THAT THAT MOTOR MIGHT HAVE A HAMONIC BALANCER ISSUE.. CHECK WITH YOUR LOCAL PARTS STORE
IF I WAS OF HELP PLEASE TELL ME.. TAHNKS JAY

Sadly you have provided only a little needed information.

Three motors came in the dodge 250

3.7 liter L6 153624
5.2 liter V-8 18436572
5.9 liter V-8 18436572

Hope this helps guide you in the correct direction to solve your problem.

r/
David

I suggest visit and check autozone.com (free register) for 1988 Dodge Truck B250 3/4 ton Van 5.2L FI 8cyl, several wiring diagrams in there.

Hope helped (remember rated this) Good luck.

you shouldnt need a diagram there should be numbers on the tension leads coming from the distibutor and numbers on the engine block near the spark plugs just match the numbers and the leads are usually different lengths, also the distibutor cap has to be in the correct position if not it is basically the same as crossing the wires and putting them in the wrong spot which will stuff up the firing order

------>>>FRONT>>>>of Van >>>>

______________________________
#5 cyl #6 cyl

#3 cyl #4 cyl

#1 cyl #2 cyl
______________________________
_________________
I COIL BLOCK I
I I
I #3 #1 #5 I
I I
I I Firing Order Is
I I 1 2 3 4 5 6
I #6 #4 #2 I
I _______________I_

the Wires Go Accordingly to prospective Terminals, So Sorry Unable to Send Pics through FixYa, A Formating Problem Exists
and they show on my end but not on your end this is TRUE and CORRECT To The BOOK other than the Lines from Coil to Spark Plug ENDS at CYLINDERS. Please dont Forget to RATE Me
Thank You And Happy Motoring!!