I have a 2002 Mercury Villager and I reversed polarity (installing new battery). Luckily, the battery stayed intact, not so luckily, the car (with new battery) is completely dead electrically. When I look in the fusible link box, I am unsure which fuses I am checking to see whether or not they are blown (I know they are labeled), but is there a specific fuse (describing the above idiotic maneuver) in which I need to be looking at?

There isn't one. Cruise Control is a joint computer operation by the BCM and ECM.

Mercury Villager (1999-2002) fuses and relays

Fuse Box Diagrams https://fuse-box.info > mercury > mercury-villager-19...

Here you will find fuse box diagrams of Mercury Villager 1999, 2000, 2001 and 2002, get information about the location of the fuse panels inside the car, ...

https://www.google.com/search?q=mobile+auto+electrician+near+me

..

How to Fix error code P0300 for random misfires on your car ...

diy-auto-repair.wonderhowto.com/.../fix-error-code-p0300-for-random-...

Oct 15, 2010 - How to Fix error code P0300 for random misfires on your car ... amisfire (code P0304) on a 1999 Mercury Villager 3.3L · How to Fix error code P0500 ... I reset my codes and it ran fine for a couple of days, then I started getting ...

(code P0305) on a 1999 Mercury Villager 3.3L - auto repair

diy-auto-repair.wonderhowto.com/.../troubleshoot-misfire-code-p0305-1...

Sep 7, 2010 - The vehicle is a '99 Mercury Village, 3.3L, with 150000 miles on it. The chief ... How to Fix error code P0300 for random misfires on your car ...

2000 Villager Misfire - Car Forums and Automotive Chat ...

www.automotiveforums.com > ... > Mercury > Villager

May 24, 2010 - 2000 Villager Misfire Villager Car Forums. ... i was told that the 3.3L engines of 1999-2002 nissan quests/ mercury villagers are INTERFERENCE engines! ... Hope the following may help, and I will post if my last fix works. ... I have a 1999mercury villager that is showing a random multiple cylinder misfire ...

Rough Idle - 2000 Mercury Villager - RepairPal

repairpal.com > Questions > Mercury > Villager > 2000 Mercury Villager

Repair the code issue, because your Villager has OBD-II which is a very helpful Diagnostic system. Upvote (4) ... My 1999 Villager was running poorly; rough idle, lack of power at highway speeds and the engine problem light indicated random miss-fire, etc. I had new spark ... Have code po306 cylinder 6 misfire detected.

P0301 - OBD-II Trouble Code - RepairPal

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Visual Inspection Chart Mechanical Electrical

• Improperly aligned window
• Damaged window mounting
• Window frame interference

• Central junction box (CJB) Fuses:
  • F30 (10A)
  • F32 (20A)
  • F34 (20A)
  • F59 (7.5A)
• Battery junction box (BJB) Fuses:
  • F20 (30A)
  • F27 (45A)
• Switches
• Circuits
• Connectors
• Heated back light
• Relays

Which window is not working ?

• Single power window is inoperative

• Front door power window switch.
• Front door power window regulator.
• Circuit.
• Driver door power window switch.

• GO to Pinpoint Test B .

Exhaust Converter Blocked ?

Did you check for combustion gases at the
coolant or radiator fill

Your down to a head gasket or a crack somewhere

I would think the head gasket is common on that
motor possibly,research that

Timing Belt worn or jumped ?

On this website you find fuse box diagram and description for Mercury Villager (2002)

https://www.autogenius.info/mercury-villager-1999-2002-fuse-box-diagram/

Transaxle is due for a rebuild

That transaxle is about the most failure
prone trans in north america

Hi.

If the radio turns on but does not operate (stays locked), then the anti theft kicked in. In that case you need to go to the nearest dealer to have the stereo unlocked.

If the radio is completely dead, then the fuse is gone. If radio is factory one, then there is one or two fuses in the in car fuse panel (they should be 15 amps if no amp is installed). Aftermarket units may also have a fuse located at the back of car radio. You will need to pull out the car stereo if that is the case.

Regards.

Ginko.

http://groups.yahoo.com/group/villagerquest/

Removal & Installation

1. Disconnect the negative battery cable.
   
2. Raise and safely support the front of the vehicle securely on jackstands.
   
3. Disconnect the VSS electrical connector.
   
4. Remove the VSS hold-down bracket bolt and remove the bracket.
   
5. Remove the VSS from the vehicle.
   
6. The installation is the reverse of removal. When installing the VSS hold-down bracket, tighten the bolt to 44–61 inch lbs. (5–7 Nm).
   

Vehicle speed sensor location

check main fuse in power box most likly blown fuse, look close some of them may not look bad but are