Question about 2004 Volkswagen Jetta

1 Answer

The check enging light comes on then goes off. I foud out the code po118 engine coolant temp circut high input. is it the coolant temp sensor. if so how do I replace it. It is on a 2004 jetta tdi

Posted by rogerolso544 on

Ad

1 Answer

Duane Wong

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Volkswagen Master
  • 6,826 Answers

According to Autozone.com:

Because ECT (engine coolant temperature) sensor procedures vary depending upon their location, first locate the part. You may need to partially drain the engine coolant to prevent coolant spillage.

  • Disconnect the negative battery cable.
  • Unplug the ECT.
  • Then, unscrew it.
  • Reverse the removal procedures to install the new part.
  • Connect the negative battery cable to the battery.



    Related Parts:
---
Cothe check enging light comes - printpage_icon.gifSensor printhe check enging light comes - 0900c152801bfc38.jpgs=



0900c152801bfc38.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Remove the coolant temperature sensor
The coolant temperature gauge sensor is a temperature-variable resistor, or thermistor. As coolant temperature increases, the resistance of the sensor decreases or decreases, depending on the type of sensor.
A1 and A2 platforms use a different type of circuit that A3 vehicles. On A1 and A2 vehicles, the circuit is a "resistance to ground" type. A3 vehicles use a "variable voltage" type, where a voltage is supplied to the sensor. Because of the circuitry design on A3 vehicles, testing of the coolant temperature gauge is limited.
The engine coolant temperature gauge uses a heat sensitive sending unit to transmit an electrical signal to the gauge. The sending unit is a heat sensitive variable resistor that is located on or near to the cylinder head and threads into an engine coolant passage. The sensors are a Negative Temperature Coefficient (NTC) type. As the temperature increases, the electrical resistance of the sensor decreases. As the coolant temperature changes, so does the resistance of the sensor. The gauge is calibrated within the operating range of the sensor and interprets the resistance value to display the coolant temperature.
Beginning with model year 1994, the engine coolant gauge and the Engine Control Module (ECM) temperature sensors were combined into one sensor with 4 terminals. The basic operation remains the same in that their resistance decreases as the coolant temperature increases, however the actual resistance values of the 2 sensor circuits are different. The elethe check enging light comes - 0900c152801bfc39.jpg the 4-wire terminal sensor ( 1 and 2 ) is keyed to prevent improper connection of the sensor's electrical circuit.

0900c152801bfc39.jpg enlarge_icon.gif

Fig. Beginning with model year 1994, the Engine Coolant Temperature Sensors combined the sensors for the ECM and the gauge into one sensor-1997 2.8L V6 sensor shown


0900c152801bfc3a.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. The electrical connector for the combined temperature sensors is keyed to avoid improperly connecting the sensor's wiring-1997 2.8L V6 connector shown

Posted on Oct 17, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p0122_p0118_p0340_p1537


P1537 intake manifold runner control stuck open

po340 camshaft position sensor a bank 1 circuit malfunction

Po118 Engine Coolant Temperature Circuit High Input

Po122 Throttle Position Sensor/Switch A Circuit Low Input



If you need further help, reach me via phone at https://www.6ya.com/expert/dennis_f849d3d6a68c6430

May 22, 2016 | Cars & Trucks

1 Answer

Trouble codes p0118 temperature po118


code p0118 refers to engine coolant temperature (ETC) sensor ---circuit malfunction===causes---coolant thermostat---wiring open circuit/short to positive---wiring short to ground---ground wire defective---ECT sensor.. The temp gauge works off a temperature sender unit separate to the coolant sensor and if it is reading 100 then it indicates an overheat situation in the engine . Probably why the engine light is coming on. As the thermostat is in the list of causes I would replace it as a precaution. The coolant sensor is what tells the CPU to turn on the electric fans to cool the radiator

Jan 13, 2014 | 2004 GMC Envoy

1 Answer

Need obd trouble codes & meanings


here r your trouble code meanings:
1) p0123-throttle position sensor circuit, high input.
2)p0117-engine coolant temperature circuit, low input.
3)p0118-engine coolant temperature ciurcuit , high input.

Jun 18, 2012 | 1997 Plymouth Breeze

1 Answer

The check engine light on a 2001 beetle read code PO118 engine coolant temperature circuit high input. what do i do?


16502/P0118/000280 From Ross-Tech Wiki Jump to: navigation, search Contents [hide] if (window.showTocToggle) { var tocShowText = "show"; var tocHideText = "hide"; showTocToggle(); } 16502/P0118/000280 - Engine Coolant Temperature Sensor (G62): Signal too High Possible Symptoms
  • Difficulties with starting a cold engine.
  • Starting the engine when engine is warmish or warm, idle rpm immediately is 1200 - 3000 rpm.
  • RPM at idle is irregular.
  • With all engine temperatures idle rpm will often vary between 900 - 1000 rpm.
  • With engine warm (90 °C) the engine temperature suddenly drops (70 °C) and slowly comes back to 90 °C.
  • Bad acceleration during warm-up.
  • Diesel Engines: Glow plug indicator may be on for a longer than normal time or at ambient temperatures where it shouldn't come on at all.
Possible Causes
  • The electrical signal coming from G62 is too low
  • Wiring and/or connections faulty (short circuit?)
  • Engine Coolant Temperature Sensor (G62) faulty
Possible Solutions
  • Check wiring and connections
  • Check / Replace Engine Coolant Temperature Sensor (G62)
Special Notes
  • In many cars between MY 1995-2002 the G2/G62 had a bad reputation for failing often. The original G2/G62 sensor is black and the improved replacements are green.

Jan 26, 2010 | 2000 Volkswagen Beetle

1 Answer

Engine coolant temp interm


the engine coolant tempurature sensor may be failing, the reason why truck stalls when light comes on is that the pcm thinks there is still a problem, then shuts down. after replacing sensor erase problem code with a obd2 scanner. if you do not have access to 1 you can go to any auto parts store and they will turn light off for free.

Dec 11, 2009 | 2004 Ford F150

1 Answer

Code po118


P0118 is Engine Coolant Temperature Circuit High voltage input. It could just be the sensor.

Aug 14, 2009 | 1999 Dodge Intrepid

2 Answers

Code PO118 chevy blazer 2002,after intake gasket replacement


hi john , sure sounds like you may have unplugged the coolant temp sensor or didn't get a good connection at the sensor , location , in between two exhaust ports on the side of the engine that has the oil fill and pcv .

J5

Jan 27, 2009 | 2002 Chevrolet Blazer

Not finding what you are looking for?
2004 Volkswagen Jetta Logo

1,364 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...