Question about Suzuki Forenza

1 Answer

I would like a diagram of the 2004 Suzuki forenza timing marks and how to get the belt aroujd the crankshaft is there a way you can give me that information?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 8,984 Answers

From autozone.com


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Disconnect the Manifold Air Temperature (MAT) sensor connector.
  4. Disconnect the air cleaner outlet hose from the throttle body.
  5. Disconnect the breather tube from the camshaft cover.
  6. Remove the air cleaner housing bolts.
  7. Remove the air cleaner housing.
  8. Remove the right front wheel.
  9. Remove the right front wheel well splash shield.
  10. Remove the serpentine drive belt.
  11. Remove the crankshaft pulley bolts and the crankshaft pulley.
  12. Remove the right engine mount bracket.
  13. Remove the front timing belt cover bolts.
  14. Remove the front timing belt cover.
  15. Using the crankshaft gear bolt, rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover.

I would like a diagram - 56340db.gif

Fig. Aligning the timing mark on the crankshaft gear with the notch at the bottom of the rear timing belt cover.


7c6bcda.gif

  1. Fig. Aligning the camshaft gears with the notches on the camshaft cover.
  2. Align the camshaft gears with the notch on the camshaft cover.
  3. Remove the timing belt.
  4. Loosen the automatic tensioner bolt. Turn the hex-key tab to relieve belt tension.

To install:
  1. Align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.
  9. Install the front timing belt cover bolts and tighten to 53 inch lbs. (6 Nm).
  10. Install the right engine mount bracket.
  11. Install the crankshaft pulley and tighten the crankshaft pulley bolts to 15 ft. lbs. (20 Nm).
  12. Install the serpentine drive belt.
  13. Install the right front wheel well splash shield.
  14. Install the right front wheel.
  15. Install the air cleaner housing.
  16. Install the air cleaner housing bolts and tighten to 89 inch lbs. (10 Nm).
  17. Connect the air cleaner outlet hose to the throttle body.
  18. Connect the breather tube to the camshaft cover.
  19. Connect the MAT sensor connector.
  20. Connect the negative battery cable.

Posted on Sep 25, 2010

Ad

1 Suggested Answer

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the timing mark on the crankshaft on 2004 Suzuki forenza


  1. Using the crankshaft gear bolt, rotate the crankshaft clockwise until the timing mark on the crankshaft gear is aligned with the notch at the bottom of the rear timing belt cover, see diagram below.


26238542-qakshaxwtqjbyy351e1gaidz-4-0.gif

Jul 15, 2016 | Suzuki Cars & Trucks

1 Answer

2004 Suzuki fortera belt diagram


which of 5+engines is it?
we can not guess that.
is it accessory belt or cam belt, cant guess that either.
at least these>?

1.4 L E-TEC I4 (petrol)
1.6 L E-TEC I4 (petrol)
1.8 L Family II I4 (petrol)
2.0 L Family II I4 (petrol)
2.0 L RA 420 I4 (diesel)

the answer was on alldata.com USA, oops no country stated (FAIL)
and
at
https://suzukipitstopplus.com/Products/1027-2004-forenza-service-manual.aspx

all the time, every day, just look.

Sep 20, 2014 | 2004 Suzuki Forenza

1 Answer

Timing procedure for 2005 suzuki forenza


what engine, most cars have many choices new.. what is yours.
"Displacement or VIN"
cam
or
spark?
btw its really a Daewoo Lacetti from S.Korea makers.
by a real FSM.
or got to alldata.com and read

here is the list of engines
1.4 L 93 bhp (69 kW) Petrol I4
1.6 L 109 bhp (81 kW) Petrol I4
1.8 L 120 bhp (89 kW) Petrol I4
2.0 L 132 bhp (98 kW) Petrol I4
2.0 L 121 bhp (90 kW) Petrol I4
2.0 L 121 bhp (90 kW) Diesel I4

before working on any car, engines. in the USA (where you?)
open hood, look up see that vacuum and smog tag there
and it tells you what engine you have,
than ask questions based on that.

the USA forenza uses the
The US model line features the 2.0 L 4-cylinder E-TEC II made by General Motors, developing a maximum power of 132 horsepower at 5600 rpm.

this is a DOHC engine, 2 cams
and a belt (rubber band engine)
cam timng, im not repeating the 38 steps in the manual or torques/
but the crank cog mark is down aligned with the bottom pan mark
the cams are both at 12pm, aligned with markes on back top pan.

install (cut and past just first 8 steps) 2.0L E-tec II only)
  1. align the timing mark on the crankshaft gear with the notch on the bottom of the rear timing belt cover.
  2. Align the timing marks on the camshaft gears, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
  3. Install the timing belt.
  4. Turn the hex-key tab in a clockwise direction to tension the belt. Turn until the pointer aligns with the notch.
  5. Install the automatic tensioner bolt and tighten to 18 ft. lbs. (25 Nm).
  6. Rotate the crankshaft two full turns clockwise using the crankshaft pulley bolt.
  7. Recheck the automatic tensioner pointer.
  8. Install the front timing belt cover.




Nov 27, 2013 | 2005 Suzuki Forenza

1 Answer

How to change timeing belt on 2008 suzuki forenza


Instructions
    • Disconnect the negative cable on your car battery. Make sure to wait for the engine of your Suzuki Forenza to cool off completely before you start working on it.
    • 2Rotate the engine using a wrench attached to a crankshaft bolt. Align the timing mark on the pulley to the 0o mark on the scale.
    • 3
    • Remove the screws and the bolts that hold the timing cover in its place and take the cover off. Loosen the bolts that hold the spring-loaded tensioner of the timing belt a little. Pull the tensioner away from the timing belt and then tighten the bolts again.
    • 4Pry off the timing belt from the pulley channels and the camshaft sprocket with a flat head screwdriver. Set the old timing belt aside and compare it with the new belt. The new belt should have the same width as with the old timing belt and the inside surface of both belts should have the same size of teeth.
    • 5Put the new timing belt on the sprockets and make sure it is positioned correctly. Loosen the bolts that hold the tensioner and pull the tensioner toward the timing belt.
    • 6Adjust the timing of the belt. Strictly follow the instructions on the Suzuki Forenza manual. When the timing is set, check if the timing marks on the can, crank and sprockets are still aligned.
    • 7Turn the engine with the wrench on the crankshaft pulley two whole circles until you reach the 0o mark.
    • 8Reinstall the timing cover and tighten the screws and bolts that hold the cover in its place.
    • 9Reconnect the negative cable on your car battery. Put the key in the ignition and start the car to check if the timing belt replacement was successful and that the car is running properly.

Jun 25, 2012 | Cars & Trucks

1 Answer

I replaced the timing belt on a 05 suzuki forenza and not i cannot figure out which mark to use on the exhaust cam pulley


  • Hear are the timing marks fora a 2005 Suzuki Forenza 2.0

  • Crankshaft gear to the bottom of the rear timing belt cover ----


ironfist109_352.jpg


  • Camshaft gear to Camshaft cover ---

ironfist109_353.jpg


  • If you have any comments please feel free to leave them here.
  • Hope this helps and thank you for using FixYa.


Regards, Tony

Oct 10, 2011 | 2005 Suzuki Forenza

1 Answer

Belt diagram


just email me i have a pdf file i can send you that has the diagram

Aug 23, 2008 | 2004 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

9,107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...