Question about 1993 Plymouth Voyager

1 Answer

How do I change the ignition switch in my 93 plymouth van?

Posted by ladyinmaine2 on

Ad

1 Answer

Jonah Oneal

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 14,092 Answers

FIRST OF ALL, TURN OFF RADIO,DISCONNECT NEGATIVE BATTERY CABLE. IF EQUIPPED WITH TILT STEERING COLUMN,REMOVE TILT LEVER.CAREFULLY REMOVE THE UPPER AND LOWER STEERING COLUMN COVERS. REMOVE THE 3 TAMPER PROOF TORX IGNITION SWITCH MOUNTING SCREWS USING SNAP ON TOOL TTXR15A2 OR EQUIVALENT. GENTLY PULL THE SWITCH AWAY FROM THE COLUMN AND REMOVE THE 2 ELECTRICAL CONNECTORS FROM THE IGNITION SWITCH. WITH THE KEY IN THE LOCK POSITION, DEPRESS THE KEY CYLINDER RETAINING PIN FLUSH WITH THE KEY CYLINDER SURFACE. ROTATE THE KEY CLOCKWISE TO THE OFF POSITION THE KEY CYLINDER SHOULD NOW BE UNSEATED. ROTATE THE KEY CYLINDER COUNTER CLOCKWISE BACK TO THE LOCK POSITION, AND REMOVE THE LOCK CYLINDER. ( TO INSTALL ) CONNECT THE ELECTRICAL CONNECTORS TO THE IGNITION SWITCH. BE SURE THE CONNECTORS ARE SECURELY LOCKED IN PLACE. MOUNT THE IGNITION SWITCH TO THE COLUMN 3 SCREWS FOR VECHICLES WITH THE TILT STEERING COLUMN THE SHIFTER MUST BE IN THE PARK POSITION AND THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG MUST BE INDEXED BEFORE THE SWITCH IS INSTALLED. PLACE SHIFTER IN THE PARK POSITION. PLACE THE IGNITION SWITCH IN THE LOCK POSITION. THE SWITCH IS IN THE LOCK POSITION WHEN THE STEERING COLUMN LOCK FLAG IS PARALLEL TO THE IGNITION SWITCH TERMINALS. POSITION THE PARK LOCK DOWEL PIN OF THE IGNITION SWITCH SO IT ENGAGES THE STEERING COLUMN PARK LOCK SLIDER LINKAGE. APPLY A LIGHT COATING OF GREASE TO THE PARK LOCK DOWEL PIN AND THE COLUMN LOCK FLAG. POSITION THE IGNITION SWITCH AGAINST THE LOCK HOUSING OPENING ON THE STEERING COLUMN. BE SURE THE SWITCH PARK LOCK DOWEL PIN ENTERS THE SLOT IN THE PARK LOCK SLIDER LINKAGE INSTALL THE RETAINING SCREW AND BRACKET. TORQUE THE SCREW TO 26 INCH LBS. INSTALL THE STEERING COLUMN COVERS AND THE TILT LEVER IF REMOVED. WITH THE KEY CYLINDER AND THE IGNITION IN THE LOCK POSITION INSTALL THE KEY CYLINDER INTO THE SWITCH UNTIL IT BOTTOMS. RECONNECT THE NEGATIVE BATTERY CABLE AND THE CHECK THE IGNITION SWITCH FOR PROPER OPERATION OF HALO LIGHT SHIFT LOCK IF EQUIPPED AND COLUMN LOCK.ALSO CHECK FOR PROPER OPERATION OF THE IGNITION SWITCH ACCESSORY, LOCK OFF, RUN AND START FUNCTIONS.

Posted on Sep 18, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1998 Plymouth Voyager van that I changed the ignition switch and now the dash lights won't go off.


Is the headlight switch in the steering column? If so you may want to take the covers off the column if you had them off earlier and look and see if you pinched a wire or put a screw in a wire. It sounds like you my have done something when you replaced the switch

If you need further help, I’m available over the phone at https://www.6ya.com/expert/edward_020b3320326d263d

Nov 10, 2013 | 1998 Plymouth Voyager

1 Answer

93 Plymouth Voyager will not start, the Fuel Pump isn't whirring when the key is turned.


You should always hear the pump. Check the electrical connections after you check to fuse.

If you need further help, reach me via phone at https://www.6ya.com/expert/chris_b82b45c59bcf133d

Dec 06, 2012 | 1997 Plymouth Voyager

1 Answer

Where is the brake booster located on the 93 grand voyager. I looked at the part on line but dont see it anywhere near the master cylinder


If your van has Antilock brakes it does not have a vacum booster.
I have the same van and the brake system is a bad design.
A 93 Plymouth/Dodge with antilock brake system and no vaccum booster but a pressure tank then it has a lifetime warrenty. Check with your local Chrysler/Dodge dealership. But first go online and get the tech sheet or recall notice.

Dec 20, 2011 | 1993 Plymouth Voyager

1 Answer

My 1999 plymouth voyager turns over but wont start


Please post Year, make, model, engine, mileage of your van.

Do you get 'spark' at the plugs?
Check engine control fuse box next to battery.
Timing jump??

Just ideas...

GL

Dec 16, 2011 | 1999 Plymouth Voyager

1 Answer

93 plymouth Voyager temp gage gets hot only when


Your electric fan is probibly not running.Fan switch,fan relay or the fan could be bad.If it is getting hot and you pop the hood you should hear the fan running.

Jan 22, 2010 | 1993 Plymouth Voyager

1 Answer

Where is the fuel pump relay switch on my 93 Plymouth Colt Vista. The book I have says it's in the engine compartment next to the ignition coil. There is no external ignition coil on my car.


you may have to take a trip to your local library and get your hands on Haynes auto repair manual for your car wish you the best of luck Michigan Man

Dec 09, 2009 | 1993 Plymouth Colt Vista

1 Answer

Takes several ''cranks'' to start van


your ignition switch might be worn or the ignition circuit might have build up resistance due to age. Some cars refuse to start when these things happen. The fix for this is a new electrical part of the ignition switch.

Good Luck

Nov 12, 2008 | 2000 Plymouth Voyager

Not finding what you are looking for?
1993 Plymouth Voyager Logo

704 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...