Theft system problem car may not restart displayed in dic

The radio displays driver information center (DIC) information when it first powers up. The uplevel radio shows the time and outside temperature on the first line of the display, and DIC information on the second line of the display.
There are 3 DIC buttons on the radio.
?€¢
ENTER

?€¢
INFO

?€¢
MENU

Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .

1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
2. Turn ON the ignition, with the engine OFF.
3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

bcm has very little to with the anti theft. you need to de active the anit theft

Go to this link for alot of info

http://vatspasslockpasskeysecurityhelp.yolasite.com/

BULLETIN NUMBER:
00-08-56-003
SECTION:
08 - Body and Accessories
DATE:
March 2000
TECHNICAL
SUBJECT:
Theft System Warning Message Displayed on Driver Information Center (DIC) (Reprogram the Vehicle Theft Deterrent (VTD) Module)
MODELS:
2001 Oldsmobile Aurora (Built prior to VIN Breakpoint H414103152)
2000 Pontiac Bonneville (Built prior to VIN Breakpoint Y4211555)
CONDITION
Some customers may comment that the SERVICE THEFT SYSTEM (Bonneville) or THEFT SYSTEM FAULT (Aurora) warning message is displayed on the DIC. The SECURITY telltale indicator may also be illuminated.
In addition, one or all of the Diagnostic Trouble Codes (DTCs) B1009, B2734 and B2947 may be set.
Important: This condition does not represent an actual system failure.
CAUSE
This condition may be due to the vehicle security status signal inputs to the VTD Module being corrupted and setting false DTCs (B1009, B2734 and B2947) and causing the SERVICE THEFT SYSTEM (Bonneville) or THEFT SYSTEM FAULT (Aurora) warning message to be displayed.
CORRECTION
If one or all of the DTCs (B1009, B2734 and B2947) have been set, reprogram the VTD Module. Use a scan tool to perform the following procedure:
Important: The Tech 2 scan tool software version 20.003 or later (North American Operations) required for reprogramming the VTD Module is available from Techline on the TIS 6 Data CD and later.
1. Select F0 - DIAGNOSTICS.
2. Enter the appropriate vehicle information (model year, vehicle type, service category).
3. Select F1 - BODY.
4. Enter the appropriate vehicle information (carline, carline series).
5. Select VTD.
6. Select F2 - SPECIAL FUNCTIONS.
7. Select F0 - DTC MASK.
8. Select DONE.
9. Select SAVE OPTIONS.
WARRANTY INFORMATION

{: ) The driver information center (DIC) displays SERVICE PARK ASSIST when the object alarm module detects a malfunction in the parking assist system and the system is disabled. The DIC also displays SERVICE PARK ASSIST when a loss of communication occurs with the object alarm module. Usually this is caused by faulty components or wirings. Better visit your dealer if still under warranty, for one park assist sensor only costs too much. If your bumper had been knocked off or had previous repairs outside the dealership, that's another thing.
The PARK ASSIST OFF message is displayed in the DIC when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged, • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

{: ) SERVICE PARK ASSIST The driver information center (DIC) displays SERVICE PARK ASSIST when the park assist module detects a malfunction in the object detection system and sends a request to the DIC for display of the message. The DIC also displays SERVICE PARK ASSIST when there is a loss of communication with the park assist module.
PARK ASSIST OFF The PARK ASSIST OFF message is displayed in the DIC when the park assist system is disabled due to conditions that disable or inhibit the system. The red LED in the rear display, as well as, the telltale in the switch will be lit, notifying the driver the PARK ASSIST system is disabled. The object alarm module requests the DIC via the serial data circuit to display PARK ASSIST OFF when it detects that one of the following conditions is true:
• The object alarm system is disabled through DIC vehicle customization feature. Refer to the Owners Manual for more information. • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, or hitch receiver. • An object is hanging out of the endgate. • The park brake is not fully released. • The system receives vibrations from a large nearby vehicle or from a heavy equipment such as a jackhammer. In the case of objects attached to the rear of the vehicle such as a trailer, hitch receiver, or a bicycle rack, or objects hanging out of the endgate, the rear parking assist (RPA) will have an Automatic Object induced disable feature where the RPA will determine if the rear object is moving with the vehicle. If the RPA detects such a condition, the park assist will be disabled. The PARK ASSIST OFF message will continue to be displayed until the trailer hitch receiver is removed and the vehicle is driven forward above 24 km/h (15 mph).

Your vehicle has a Driver Information Center (DIC).
All messages will appear in the DIC display located
below the speedometer in the instrument panel cluster.
The DIC buttons are located on the instrument panel,
to the left of the instrument panel cluster.
The DIC comes on when the ignition is on. After a short
delay, the DIC will display the information that was
last displayed before the engine was turned off.
The DIC displays trip, fuel, and vehicle system
information, and warning messages if a system problem
is detected. The bottom line of the DIC shows the
shift lever position indicator. See Automatic
Transmission Operation on page 3-23 for more
information.
If your vehicle’s DIC has these features, the compass
direction and the outside air temperature may also
display on the DIC when viewing the trip and fuel
information. The compass direction appears on the top
right corner of the DIC display. The outside air
temperature automatically appears in the bottom right
corner of the DIC display. If there is a problem with the
system that controls the temperature display, the
numbers will be replaced with dashes. If this occurs,
have the vehicle serviced by your dealer/retailer.
The DIC also allows some features to be customized.
See DIC Vehicle Customization on page 4-66 for
more information.
DIC

i beleive those have their own door switches in latch i would try to clean latches with spray brake kleen then blow out, lube with a spray lube like wd40 that may solve your issue. while your doing this remove negative battery cable so the ecm has to recheck doors system.

if you got climate control air conditioner control buttons turn on ignition key enter the self diagnostic system. select pcm override ps13 tps sensor learn.press the warmer button. the driver information center should display 09.indicating that the garage shift value has been reset.select pcm override ps14 tran adapt.press the cooler button the dic should display90 indicating the up shift adapt value been reset.press warmer button the dic should display 09 indicating the steady state adapt value has been reset. press and hold the off and rear defog buttons on dic until the message .transaxle oil life reset is displayed on the dic.