1999 ford ranger timing marks 2.5 - 1999 Ford Ranger SuperCab

SOURCE: need timing marks ford ranger

The timing marks are on your timing belt cover. There is a little circle on the bottom right of the cover near the harmonic balancer that you can pop out to see if your distributor accesory gear is in the correct position. The camshaft has a triangle on the inside of the gear that you can line up with this accesory gear. The bottom of the timing belt cover has your timing tick marks and you may have to clean off this rectangular piece that is sticking out on the cover to see the marks. A good timing gun and remembering where the number 1 cylinder on your distributor is a good start to timing your motor. Refer to a Haynes Manual and it will give you a good guide line on how to time your motor with TDC. I hope you have good luck with this!

Greg Bernett

• 2993 Answers
• Posted on Jul 26, 2009

SOURCE: 1999 kia sportage timing marks

Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks

1. Align marks on camshaft pulleys with alignment marks on seal plate.
2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
   
3. Loosen tensioner lock bolt.
4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
8. NOTE: Replace tensioner spring if timing belt deflection is excessive.

1. Install lower timing belt cover.
2. Install upper timing belt cover.
3. Install power steering drive belt and adjust belt tension.
4. Install fan pulley.
5. Install generator drive belt and adjust belt tension.
6. Install A/C drive belt and adjust belt tension.
7. Install splash guard.
8. Install fan and fan shroud.
9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
10. Install fan shroud mounting bolts.
11. Install fresh air duct.
12. Connect hose to resonance chamber.
13. Connect battery negative cable.

SOURCE: Timing marks on 1999 Ford Ranger 2.5L.

Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

1. Loosen the alternator retaining bolts and remove the drive belt from the pulleys. Remove the water pump pulley.
2. Loosen and position the power steering pump mounting bracket and position it aside.
3. Remove the four timing belt outer cover retaining bolts and remove the cover. Remove the crankshaft pulley and belt guide.
4. Loosen the belt tensioner pulley assembly, then position a camshaft belt adjuster tool (T74P-6254-A or equivalent) on the tension spring rollpin and retract the belt tensioner away from the timing belt. Tighten the adjustment bolt to lock the tensioner in the retracted position.
5. Remove the timing belt.

1. Install the new belt over the crankshaft sprocket and then counterclockwise over the auxiliary and camshaft sprockets, making sure the lugs on the belt properly engage the sprocket teeth on the pulleys. Be careful not to rotate the pulleys when installing the belt.
2. Release the timing belt tensioner pulley, allowing the tensioner to take up the belt slack. If the spring does not have enough tension to move the roller against the belt (belt hangs loose), it might be necessary to manually push the roller against the belt and tighten the bolt.

1. Rotate the crankshaft two complete turns by hand (in the normal direction of rotation) to remove the slack from the belt, then tighten the tensioner adjustment and pivot bolts to specifications. Refer to the necessary illustrations. Make sure the belt is seated properly on the pulleys and that the timing marks are still in alignment when No. 1 cylinder is again at TDC/compression.
2. Install the crankshaft pulley and belt guide.
3. Install the timing belt cover.
4. Install the water pump pulley and fan blades. Install upper radiator hose if necessary. Refill the cooling system.
5. Position the alternator and drive belts, then adjust and tighten it to specifications.
6. Start the engine and check the ignition timing. Adjust the timing, if necessary.

SOURCE: what do the timing belt marks line up on a 94 ford

My apologies for the delayed response. I am going back to answer unanswered questions.
CLICK on the following LINK. It has the Timing Belt & Mark(s) Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my sincerest apologies...
Thanks!

http://www.2carpros.com/car_repair_information/year/1994/make/ford/model/ranger/1994_ford_ranger_timing_belt_diagram_marks.htm

lacroixx1

• 101 Answers
• Posted on Jun 16, 2010

SOURCE: 1999 ford ranger 4.0 engine code p1151

are all codes for the o2 sensor