Washer fluid not working...installed new pump...no washer fluid again!! what should i do next??

Assuming the washer fluid is topped up! When you activate the washers can you hear the washer motor buzzing?

make sure you have washer fluid come out of the pump when on,if so maybe clogged hose to nozzle or nozzle clogged up which you can clean chemical residues with a sharp needle then moderately blow air(with air hose) from nozzle towards end of hose that connects to pump. Hope this helps. Oh,make sure not to wiggle the nozzle because then it would change direction of spray.

If the washer fluid is not pumping and they're new, something isn't connected right. They're obviously not getting power. Either that or the pumps didn't work in the first place.

The same tank that holds the front wiper washer fluid holds the rear. If your rear washer is not working, it could be one of 2 things.....

1- your washer fluid tank is low. Most car manufacturers design the tank so the rear washers stop getting fluid first to remind you to fill the tank.

2- there is a clog in your rear washer system or the pump is not working. Your problem sounds like your pump is working, so first top off your washer fluid tank, then if after about 30 seconds of trying (it takes a while to get back there), try to first unplug the rear washer by scrubbing with a toothbrush and hot water. Next, follow the hose to see if it is pinched somewhere or broken.

One can get a repair kit that includes a new motor pump and wiring clips, or

one can get the original motor that plugs into the windshield wiper fluid reservoir.

---
Windshield wiper reservoir (gives idea of how to change the windshield wiper fluid pump motor) Removal & Installation To Remove:

1. Disconnect and isolate the negative battery cable.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and splash shield.
4. Disconnect the electrical connectors from the pumps and detach the rear washer hose.
5. Place a drain pan under the reservoir if it contains fluid.
6. Disconnect the front washer hose at the wiper unit in the engine compartment. NOTE: The front hose will be removed with the reservoir.
   
7. Let the fluid drain from the reservoir.
8. Remove the mounting screws and the reservoir.

To Install:

1. Install the fluid reservoir with the mounting screws.
2. Connect the front washer hose in the engine compartment.
3. Connect the electrical connectors and rear washer hose.
4. Install the splash shield.
5. Install the right front wheel.
6. Lower the vehicle.

Open the hood and locate your washer fluid reservoir. This is normally located on the driver's side of the engine bay.Locate the fluid pump. It should be underneath the reservoir.Remove the bolts holding the pump to the vehicle's frame.Remove the electo the pump.Install the new washer pump. Installation is the reverse of removal.vote for me if it helps you and you can write a testimonial also.

On the drivers side of the vehicle just behind the front bumper is the washer fluid reservoir. The washer pumps (2 - one for the back and one for the front) are located ont the face of the reservoir.

1) Drain the resevoir. (You can reuse this fluid, so put it in a clean container)
2) Disconnect the wiring harness for the problem pump.
3) Remove the sprayer line.
4) Remove the pump. It is held in by being snapped into a channel on the resevoir and by the rubber grommet. This may take some elbow grease.
5) Remove the old grommet.(If your new pump came with a new grommet)

Installation is reverse. Usually new pumps come with new grommets. If not, it is ok to reuse the old one.

Your wiper motor most likely burnt out. And your washer fluid pump did the same.

take it back

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).