Question about 2002 Acura 3.2TL

1 Answer

Throwing code P1750, checked the solenoids and they were fine. Tranny was replaced at 90,000 miles, it is at 120,000 miles now. It's hard for it to shift into gears, which is confusing considering that it is usually the gears slip down when the tranny is going out. I need serious help on this!!

Posted by naludivawahi on

Ad

1 Answer

David Harrelson

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 5,440 Answers

When tranny was replaced, were all lines and trans cooler flushed? Was converter replaced? Try flush and refill trans fluid and replace filter.

Posted on Feb 02, 2018

Ad

5 Related Answers

Anonymous

  • 132 Answers

SOURCE: Locationof the Torque Converter Clutch Solenoid

Your transmission should still work if the solenoid goes bad. It will just shift funny

Posted on Jan 30, 2009

Ad
emissionwiz

Marvin

  • 85239 Answers

SOURCE: tranny in 2003 trailblazer

there are 4 solenoids in the trans, three shift and one torque converter clutch solenoid. Solenoid B is 2-3 shift solenoid.

Posted on Apr 07, 2009

bryant

  • 53 Answers

SOURCE: 2002 neon tranny faiure??

I had the same problem driving along and had to coast over to the side of the road. 92000km. all the clutches in the tranny were gone and all kinds of filings in filter and pan. the tranny had to be rebuilt at dealer for $1895 canadian Sorry for this news I also thought it slipped into neutral and wouldn't move no matter where I put the shifter

Posted on May 01, 2009

gambit3rogue

gambit3rogue

  • 106 Answers

SOURCE: tranny slips & wont shift past 2nd gear

tranny slips can also mean that you may need to change the tranny filter. But just like cooking oil at first it is thick then you add heat and it gets thinner, same for tranny oil which could also mean that your tranny needs gear and plate work. The easiest way to find out is to insert the oil dip stick, clean it with a paper towel and check to see if you can see metal shivers or if the color of the tranny oil is not red but silverish, these are usually indictative of a tranny that needs an overhaul. hope this helps.

Good Luck =)

Posted on May 21, 2009

Anonymous

  • 15 Answers

SOURCE: 2001 dodge ram 2500 5.9l automatic 2wd. code

go to google.com, type in P0753 dodge code. when you get your search results,it should be the second one down,it should look something like what I typed after this at the bottom part of the second result,maybe the 3rd.instead of ma trying to explain it again,just go there and you will find a detailed list of how to check and test,and even replace all parts associated with this code,there is even pictures to look at also. www.cumminsforum.com/.../167007-code-p0753-repaired-long.html

Posted on Oct 10, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a Mitsubishi Montero sport 1998 code p1750 need picture of location


Picture of location for what ?
First thing to do with any transmission codes is check the fluid and clear the codes after recording them then redo a test drive cycle

A P1750 can be anything from a wiring short or a bad TCM

It could be the converter clutch solenoid, shift control solenoid, pressure control solenoid or engine control module has failed.

If the code comes back then you will have to check the wiring harness to the transmission and test the solenoid pack and see if they are malfunctioning ! Your best bet , take it to a qualified repair shop .

Dec 29, 2016 | 1998 Mitsubishi Montero Sport

1 Answer

Transmission slipping... no check engine light on... miles under 90,000


If it told you to check the transmission, there's a code stored. But chances are it's an enhanced code or a U, C or B code that your code reader can't read. A professional scan tool is needed to read those codes. The computer never posts a message without setting a code. NEVER.

Nov 11, 2017 | 2005 Ford Taurus

1 Answer

Code p 1750


DTC P1750: Mechanical Problem in Hydraulic Control System for A/T Clutch Pressure Control Solenoid Valves A and B, or Problem in Hydraulic Control SystemBelow is the Honda procedure to determine.Turn the ignition switch OFF.Replace the A/T clutch pressure control solenoid valves A and B.Reset the PCM memory by removing the BACK UP fuse in the passenger's under-dash fuse relay box for more than 10 seconds.Drive the vehicle for several minutes in 1st, 2nd, 3rd, and 4th gears in [D4] position.

Recheck for code P1750.

Hope helps.

Apr 16, 2012 | Mitsubishi Galant Cars & Trucks

2 Answers

2000 blazer shifts fine 1-3 gears , wont go into overdrive, shows check engine light trouble code po0753 shift solenoid a , any help


OK, let me remember..........the code 753 means the solenoid INSIDE the tranny pan is bad. You don't have 1st or 4th gear, is what I was told, however, you probably WON'T even notice. I didn't. If you are at a stop, and get on it hard, you should be able to tell. If you drive normal, like me, and just accelerate gradually, you would not be able to tell that the truck is not hitting the 1st and 4th gear. You may not recognize a problem, just the check engine light. Your going to have to drop the tranny pan, replace the solenoid, and reinstall the fluid and the pan. The hardest part is, upon dropping the pan, if you don't know what you are doing, you can damage the other solenoids, and if you don't damage any, you may still have a hard time realizing which solenoid is the right one. It would take 1hour at, plus tranny pan gasket and fluid, etc., etc., for a total of about $120. Most transmission shop charge $100 for a transmission oil and filter service. The solenoid was about $20. It is not hard to replace, just unclip the wire harness and solenoid which will be an extra 5 min to the service time.

Nov 03, 2009 | Chevrolet Blazer Cars & Trucks

1 Answer

Have a transmission code P1750 on 1998 Mitsi Ecplise Spyder GS . I had the transmission rebuilt about a year ago,the check engine light came on and I had it diagnosed .The mechanic checked it out and said...


p1750 is a Manufacturer Control Transmission. i work at advance auto parts and we get these codes in from time to time. what i tell people is alot of times it is infact your solenoid box assemble is going. what that does is to tell your transmission when to shift into gears. im assuming your car is having a hard time shifting gears. to replace that part your looking to spend about 200 to 500 with parts and labor. unless you want to do the job yourself. than if im right it should run you between 150 to 200 for the part.

Oct 14, 2009 | 1996 Mitsubishi Eclipse

3 Answers

My 2002 honda has a transmission problem went to autozone to check on there computer it came up with p1750 code thought it was low fluid but i added fluid and it did not help the check eng light is still...


If I am not mistaken isn't that a shift solenoid code. If it is a shift solenoid code you will need to service the tranny and have it replaced. You can also check and see it there are any service bulletins or recalls on the tranny system through your local dealer.

Sep 26, 2009 | 2002 Honda Accord

1 Answer

Tranny does not shift out of O/D and starting out in 2nd gear.


Same situation, Solenoids in the Transmission were throwing the codes, Lost O/D and had transmission replaced. No signs of problems after check engine light came on for close to 1000 miles later.

Aug 21, 2009 | 2000 Hyundai Elantra

2 Answers

P 1750 cod come up. has shifting problem.


DTC P1750: Mechanical Problem in Hydraulic Control System of A/T Clutch Pressure Control Solenoid Valve Assemblies A and B, or Problem in Hydraulic Control System

NOTE:
• Record all freeze data and review General Troubleshooting Information before you troubleshoot.
• Keep these replacement solenoid valves on hand:
• A/T clutch pressure control solenoid valves A and B
1. Check whether the OBD II scan tool indicates another code. Does the OBD II scan tool indicate another code? YES - Perform the troubleshooting flowchart for the indicated code(s). Recheck for code P1750 after troubleshooting. NO - Go to step 2.
2. Turn the ignition switch OFF.
3. Replace the A/T clutch pressure control solenoid valves A and B.
4. Reset the PCM memory with the PGM Tester or by removing the BACK UP fuse in the passenger's underdash fuse/relay box for more than 10 seconds .
5. Drive the vehicle for several minutes in 1st, 2nd, 3rd, 4th, and 5th gears in the position.
6. Recheck for code P1750. Does the OBD II scan tool indicate code P1750? YES - Replace the transmission. NO - The problem has been corrected

Jul 08, 2009 | Acura TL Cars & Trucks

1 Answer

Code p1750


P1750 Solenoid Assembly Malfunction. The TCU is sending a fail signal to the ECU.
It's more like a transmission problem. Bad solenoid in the transmission.

Apr 04, 2009 | 1998 Mitsubishi Galant

2 Answers

My ransmission on my 2004 chevy monte carlo shifts hard


Hook that diagnostic computer to the car. If the cod reads P1810 then u need a Pressure Control Solenoid. Your check engine light will not come on with this code. The mechanic will have to drop the transmission to install the solenoid. Have a 2000 pontiac bonneville that had the same problem and ever since I did the solenoid change I have had no other problems.

Jan 17, 2009 | 2004 Chevrolet Monte Carlo

Not finding what you are looking for?
2002 Acura 3.2TL Logo

Related Topics:

1,130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

john h

Level 3 Expert

23515 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...