What do i do when the air suspension does not work?

Lincoln Town Car Questions - Rear suspension - CarGurus

www.cargurus.com > Questions > Lincoln > Town Car

CarGurusFeb 7, 2015 - Rear suspension - Should the rear airbags deflate after I turn off ...seems to be no leaks cause the pump turns off and I don't hear it going off and on whiledriving. ... dead so you have leak when you jacked up car if not turn off air you could... car pumps up and bleeds off later the problem is NOT the leveler.

2002 Lincoln TC Air suspension not working - CarGurus

www.cargurus.com > Questions > Lincoln > Town Car

CarGurusJul 23, 2012 - 2002 Lincoln TC Air suspension not working - My 2002 TC airsuspension ... 2012 at 09:25 PM about the 2002 Lincoln Town Car Executive ... I did not pay attention that you said the compressor is OK. ... Rear Air Suspension 2 answers ... How can I test my Air suspension height leveling sensor on my 1997 ...

That could work , You mite be able to test the sensor in question with ohm meter . Test the front one an see what the resistance is ,then check the back one. I don't know what it should be with out looking it up in the service info . You could also check to see if the sensor is getting power from the control module , an see if there is a return input to the module .
There are a few DTC'S this able to set !
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTCs Description Source Action B1318 Battery Voltage Low Air Suspension Control Module Go To Pinpoint Test C . B1342 Air Suspension Control Module Air Suspension Control Module INSTALL a new air suspension control module. REFER to Module-Air Suspension Control . SET the front ride height. REFER to Air Suspension Initialization (Clear DTC B2140). CLEAR the DTCs. REPEAT the self-test. B1485 Brake Pedal Input Circuit Battery Short Air Suspension Control Module RERUN On-Demand Self-Test. MAKE SURE that the brake pedal is not pressed. If DTC is returned again, REPAIR brake pedal position (BPP) circuitry. B1566 Door Ajar Circuit Short to Ground Air Suspension Control Module Go To Pinpoint Test D . B2140 Initialization Failure (Vehicle Ride Height Not Programmed) Air Suspension Control Module REFER to Air Suspension Initialization (Clear DTC B2140). C1439 Vehicle Acceleration EEC-V Circuit Failure Air Suspension Control Module Go To Pinpoint Test E . C1724 Air Suspension Height Sensor Power Circuit Failure Air Suspension Control Module Go To Pinpoint Test F . C1726 Air Suspension Pneumatic Failure Air Suspension Control Module Go To Pinpoint Test G . C1760 Air Suspension Height Sensor High Signal Circuit Failure Air Suspension Control Module Go To Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test I . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test J . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module Go To Pinpoint Test K . C1830 Air Suspension Compressor Relay Circuit Failure Air Suspension Control Module Go To Pinpoint Test L . C1917 Steering Electronic Variable Orifice (EEVO) Out-of-Range Fault Air Suspension Control Module Go To Pinpoint Test Q .

• Uneven vehicle height

• Circuitry.
• Rear pneumatic fault.
• Air compressor assembly.
• Air suspension control module.

• Go To Pinpoint Test I .

Your best bet take it an have it diagnosed ! This is computer controlled an may have DTC'S - diagnostic trouble codes stored !
C1724 Air Suspension Height Sensor Power Circuit Failure Air Suspension Control Module GO to Pinpoint Test F . C1726 Air Suspension Rear Pneumatic Failure Air Suspension Control Module GO to Pinpoint Test G . C1760 Air Suspension Rear Height Sensor High Signal Circuit Failure Air Suspension Control Module GO to Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Air Suspension Control Module GO to Pinpoint Test I . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module GO to Pinpoint Test J . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Air Suspension Control Module GO to Pinpoint Test K . C1830 Air Suspension Compressor Relay Circuit Failure Air Suspension Control Module GO to Pinpoint Test L
Symptom Chart Condition Possible Sources Action

• No communication with the air suspension control module

• CJB Fuse 4 (15A), 6 (5A) and 20 (5A).
• Circuitry.
• Air suspension control module.
• Air suspension switch.

• GO to Pinpoint Test A .

You replaced a part that you probably didn't need !

• The compressor is inoperative

• BJB Fuse 109 (50A).
• Air compressor assembly.
• Circuitry.
• Air suspension relay.

• GO to Pinpoint Test Q .

There is a lot to this system an guessing as to what the problem is ,isn't the way to fix it.
Measure the voltage between air compressor relay C1000 Pin A, Circuit 1053 (LB/PK), harness side and ground.

• Is the voltage greater than 10 volts?

Yes GO to Q3 .

No REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
Measure the resistance between air compressor C1000 Pin B, Circuit 538 (GY/RD), harness side and air compressor assembly C194M Pin 4, Circuit 538 (GY/RD), harness side.

• Is the resistance less than 5 ohms?

Yes GO to Q4 .

No REPAIR the circuit. CLEAR the DTCs. REPEAT the self-test.
Air Suspension Height Sensor
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3.2 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm (3.2 in) of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket). Replace the air suspension height sensor as a unit.
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.

• A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.
• Air Suspension Control Module
  NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
  NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
  The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing the vehicle and related components.
  The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.

For help with Town Car Air Suspension problems, American Air Suspension is the best place to go....and yes, not only do I work there....I own the company! For almost half the cost of the where the last guy was advertising, you can do away with your air suspension problems forever with a Town Car Air Suspension Conversion

Having it hooked up to a factory scan tool would be your best bet . Check for DTC'S diagnostic trouble codes . Without testing ,code scan ,we'd only be guessing .
Very complex , the untrained person hasn't got a pray of fixing this . You have no idea what your dealing with . Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:

• Rear air suspension control (RAS) module (5A919)
• Snorkel
• Drier
• Air compressor (5319)
• Air suspension switch (5K761)
• Solenoid valve (5311)
• Air spring (5560)
• Air suspension height sensor (5359)
• Air line
• Rear Air Suspension Control Module
  A microprocessor controls the air suspension system. The microprocessor and its supporting hardware are contained in the rear air suspension control module. The rear air suspension control module responds to signals from various sensors in the vehicle to maintain the programmed ride height while the vehicle is either moving or stopped. The rear air suspension control module accomplishes this by opening and closing solenoid valves to control the amount of air in the air spring(s). The rear air suspension control module turns on the compressor by applying voltage through the compressor relay to inflate the air spring(s) and raise the vehicle. The rear air suspension control module opens the vent solenoid to lower the vehicle by releasing air from the air spring(s) in response to signal inputs from the air suspension height sensor(s).
• Rear Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1317 Battery Voltage High Rear Air Suspension Control Module GO to Pinpoint Test C . B1318 Battery Voltage Low Rear Air Suspension Control Module GO to Pinpoint Test C . B1342 ECU Is Defective Rear Air Suspension Control Module INSTALL a new rear air suspension control module. REFER to Module-Air Suspension Control . TEST the system for normal operation. C1441 Steering Sensor Channel A Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1442 Steering Sensor Channel B Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1722 Air Suspension Height Sensor Power Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1723 Air Suspension Height Sensor Power Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test E . C1760 Air Suspension Rear Height Sensor High Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1763 Air Suspension Rear Height Sensor High Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test G . C1765 Air Suspension Rear Height Sensor Low Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1768 Air Suspension Rear Height Sensor Low Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test I . C1773 Air Suspension Vent Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test J . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test K . C1793 Air Suspension LR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test L . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test M . C1798 Air Suspension RR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test N . C1813 Air Suspension Vent Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test O . C1818 Air Suspension Air Compressor Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test P . C1830 Air Compressor Relay Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test Q . C1832 Air Compressor Relay Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test R . C1840 Air Suspension Switch Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test S . C1842 Air Suspension Switch Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1897 Steering VAPS Circuit Loop Failure Rear Air Suspension Control Module REFER to Section 211-00 . U1041 SPC Invalid or Missing Data for Vehicle Speed

LEAK IS AIR LINE FROM COMPRESSOR TO REAR SUSPENSION
OR...REAR SUSPENSION COMPONENT FAILURE

SOUND LIKE AIR SPRING ELECTRICAL SOLENOID.NO YOU SHOULD NOT HEAR NO NOISE COMING FROM AIR SHOCKS.THIS IS A DEALERSHIP JOB DANGEROUS JOB IF YOU HAVE NOT WORK ON AIR SPRINGS SUSPENSION BEFORE.YOU HAVE TO TURN OFF AIR SUSPENSION SWITCH FIRST BEFORE LIFTING VECHICLE.IF YOU DONT THE AIR SPRINGS WILL OVER EXTEND CAUSING DAMAGE TO AIR SPRINGS.

start here

The air suspension system is designed to improve ride, handling and general vehicle performance for static, on-road and off-road driving condition:

• Ride is improved by using an air type spring (the soft ride is inherent).
• Handling is improved by maintaining constant vehicle attitude.

The system consists of unique rear air springs, air compressor, air lines, air spring solenoids, height sensor, air suspension control module, attachments and associated signals derived from both driver and road inputs. With these components and signals, the air suspension control module commands changes in vehicle height that are necessary for the load leveling features.
The load leveling feature rear air suspension (RAS) systems shall automatically make adjustments in vehicle height so that the vehicle is always at trim height and constant front-to-rear vehicle attitudes are maintained over the expected load range of the vehicle. Adjustments in height that are necessary to correct height differences between the vehicle's left and right sides for RAS system shall be restricted to what can be reliably achieved with one air suspension height sensor.
The system uses one air suspension height sensor, a steering sensor, generic electronic module (GEM) transfer case inputs, and other vehicle sensors to measure driver and road inputs. The system changes vehicle height using an air compressor, two air lines, and the use of an air spring with an air spring solenoid.
The air suspension system holds vehicle height when the rear hatch or any door is opened. The system stores rear vehicle height the moment any open door is detected. The system then maintains this height regardless of the addition or removal of a load. The system will return to its commanded height when all doors are closed and the vehicle speed exceeds 16 km/h (10 mph).
Air Suspension Switch
The air suspension switch is located behind the RH kick panel on a mounting bracket. The switch interrupts power to the air suspension control module.
The air suspension switch supplies a signal to the air suspension control module. Without the air suspension control module receiving this signal the load leveling system is inoperative and will not react when rear of the vehicle is raised or lowered. If the air suspension system is disabled by turning off air suspension switch, a "CHECK SUSP" will appear in the RH corner of the instrument cluster with the ignition in the run position.
Air Compressor
The RAS air compressor:

• Is not interchangeable with four wheel air suspension (4WAS) compressor.
• Consists of the compressor and vent solenoid; neither are replaceable as individual items.
• Is mounted in the engine compartment between the washer fluid bottle and headlamp (RH front corner).
• Is a single cylinder electric motor driven unit that provides pressurized air as required.
• Is powered by a solid state relay, controlled by the air suspension control module.
• Passes pressurized air through the compressor air drier that contains silica gel (a drying agent). Moisture is then removed from the compressor air drier when vented air passes out of the system during vent operation.
• Air drier has a single port and is not interchangeable with 4WAS compressor air drier.
• Air drier may be replaced separately.
• Incorporates a snorkle that may be replaced separately.

The vent solenoid:

• Allows air to escape from the system during venting actions.
• Is located in the air compressor cylinder head.
• Has a 160 psi internal relief valve.
• Shares a common electrical connector with the air compressor motor.
• Is enclosed in the cylinder head casting, which forms an integral valve housing that allows the valve tip to enter the pressurized side of the system.
• Has an O-ring seal that prevents air leakage past the valve tip.
• Opens when the air suspension control module determines lowering is required.
• Provides an escape route for pressurized air that opens when system pressures exceed safe operating levels.
• Is replaced with the air compressor as a unit.

Air Spring
RAS vehicles use air springs in the rear. The air springs provide a varying spring rate proportional to the systems air pressure and volume. The air suspension system regulates the air pressure in each air spring by compressing and venting the system air. Increasing air pressure (compressing) raises the rear of the vehicle while decreasing air pressure (venting) lowers the rear of the vehicle. Vehicle height is maintained by the addition and removal of air in each air spring through an air spring solenoid installed in the upper spring cap and energized through the air suspension control module.
The air springs are mounted between the axle spring seats and the frame upper spring seats.
The two air springs replace the conventional rear coil springs.
Air Suspension Height Sensor
When the air suspension height sensor indicates that the rear of the vehicle is lower than trim under normal driving conditions, the air compressor will turn on and pump compressed air to the air springs. When the sensor indicates that the rear of the vehicle is raised above trim under normal driving conditions, this will cause the air to be vented from the air springs to lower the vehicle back to its trim height level.
One air suspension height sensor is mounted on the vehicle. The air suspension height sensor sends a voltage signal to the air suspension control module. The output ranges from approximately 4.75 volts at minimum height (when the vehicle is low or in full jounce), to 0.25 volts at maximum height (when the vehicle is high or in full rebound). The air suspension height sensor has a useable range of 80 mm (3 in) compared to total suspension travel of 200-250 mm (8 to 10 in) at the wheel. Therefore, the air suspension height sensor is mounted to the suspension at a point where full rear suspension travel at the wheel is relative to 80 mm of travel at the air suspension height sensor. The air suspension height sensor is attached between the No. 5 frame crossmember (upper socket) and the panhard rod (lower socket). Replace the air suspension height sensor as a unit.
Compressor Relay
The compressor relay is energized by the air suspension control module to allow high current to flow from the battery to the compressor motor.

• A solid state relay is used in the air suspension system for air compressor control. The relay incorporates a custom power metal oxide semi-conductor field effect transistor (MOSFET) and ceramic hybrid circuitry. The relay switches high current loads in response to low power signals and is controlled by the logic of the air suspension control module.

Air Suspension Control Module
NOTE: The 4WAS air suspension control module is used for the RAS system. The internal processor recognizes external circuitry to determine if it is installed in a 4WAS or a RAS equipped vehicle.
NOTE: The air suspension control module is calibrated with information from the air suspension height sensor. A new or exchanged air suspension control module requires a ride height adjustment calibration process to be performed.
The air suspension control module controls the air compressor motor (through a solid state relay), and the air spring solenoids. The air suspension control module also provides power to the air suspension height sensor. The air suspension control module controls vehicle height adjustments by monitoring the air suspension height sensor, vehicle speed, a steering sensor, acceleration input, the door ajar signal, transfer case signals, and the brake pedal position (BPP) switch. The air suspension control module also conducts all fail-safe and diagnostic strategies and contains self-test and communication software for testing of the vehicle and related components.
The air suspension control module is mounted in the passenger compartment inside the instrument panel above the radio and temperature controls.
The air suspension control module monitors and controls the air suspension system through a 32-pin two-way connector. The air suspension control module is keyed so that the air suspension control module cannot be plugged into an incorrect harness. There are two sides of the harness connection to the air suspension control module. Each is uniquely colored and keyed to prevent reversing the connections.
Air Suspension Diagnostic Connector
The air suspension diagnostic connector is used to aid the technician in diagnosing the air suspension system. It is also used to vent the system of compressed air when air suspension system components need to be repaired or replaced. The air suspension diagnostic connector is located under steering column.

Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:

• Rear air suspension control (RAS) module (5A919)
• Snorkel
• Drier
• Air compressor (5319)
• Air suspension switch (5K761)
• Solenoid valve (5311)
• Air spring (5560)
• Air suspension height sensor (5359)
• Air line

------------------------------------------------
Visual Inspection Chart Mechanical Electrical

• Restricted suspension movement
• Excessive vehicle load
• Cut, severed, or crimped air line(s)
• Damaged air spring(s)
• Height sensor damage
• Height sensor mounted incorrectly, disconnected, or damaged

• Central junction box (CJB):
  • Fuse 5 (15A)
• Battery junction box (BJB):
  • Fuse 8 (30A)
• Loose or corroded connectors
• Air suspension switch OFF

The air suspension control module is diagnosed using Super Star II Tester 418-F045 (007-0041B) or equivalent.
The test connector used to communicate with the air suspension control module is located on the RH side of the luggage compartment.
When the tester is connected, the engine is started and the HOLD/TEST button is latched down, the air suspension control module will respond sending a code 10 to the Super Star II Tester which represents "Diagnostics mode entered." If diagnostic trouble code (DTC) 10 is not displayed, go to Pinpoint Test A.
Air Suspension Control Module Diagnostic Trouble Code (DTC) Index
Condition Possible Sources Action

• No communication with the air suspension control module

• CJB Fuse 5 (15A).
• BJB Fuse 8 (30A).
• Circuitry.
• Air suspension control module.

• GO to Pinpoint Test A .

• Unable to enter auto test

• Air suspension control module.
• Circuitry.

• GO to Pinpoint Test B .

• Rear air suspension does not respond to load changes

• Circuitry.
• Air compressor.
• Air compressor inlet tube.
• Air compressor drier.
• Air suspension height sensor.
• Air suspension control module.

• GO to Pinpoint Test C .

• Rear rides low/high

• Circuitry.
• Air spring solenoid.
• Air suspension height sensor.
• Air suspension control module.

• GO to Pinpoint Test C .

• Poor ride quality

• Circuitry.
• Air springs.

• GO to Pinpoint Test C .

• Air suspension warning indicator ON

• Air suspension switch OFF.

• Place the air suspension switch in the ON position.

• Air suspension control module.
• Circuitry.

• GO to Auto Test.

• Instrument cluster (conventional cluster) or lamp warning module (electronic cluster).

• REFER to Section 413-01A (conventional cluster) or REFER to Section 413-01B (electronic cluster), or REFER to Section 413-01C (natural gas cluster).

i have a 99 lincoln town car and the rear air ride don't work the back of the car is hitting the ground how do i fix that