Involved vehicle: 1999 Saturn SL - 4 cyl, 5 speed manual I have two problems: PROBLEM #1: when I turn on the windshield wipers - any position ( mist, intermittent, slow or fast) I can not turn them off - wipers only stop when I turn off the engine and the wiper blades are in the park position. When they are going there is only one speed - slow and steady. PROBLEM #2: involves engine speed - When I start car - RPM goes to 2K RPM and stays there even after warming up. When I shift into 1st or reverse to get going this brings the RPM down, but when I push in the clutch to shift to 2nd, 3rd, 4th or 5th gear the RPM goes back to 2K. The RPM only drops down to 900 or 1,000 when I come to a stop at a stop sign or red light - then, once stopped after 20- 30 seconds the RPM slowly drops down to 900 - 1,000. I seems to have some connection to forward motion because RPM only drops when stopped. If I am going 50 MPH down hill and shift into neutral, the RPM stays at 2K. RPM does not drop when I take foot off of gas and push in the clutch to shift - if not at 2K before the clutch is pushed in it goes to 2K as soon as I push it in to shift. I can go 30 MPH in 3rd gear with my foot off of the gas Any Help?? Tony Notari

If the windshield wipers on your 2002 Corvette won't shut off, it could indicate a problem with the wiper control switch or a malfunction in the wiper motor circuit. Here are some troubleshooting steps you can try:

1. Check the wiper control switch: Ensure that the wiper control switch is in the "Off" position. Sometimes, the switch can get stuck or malfunction, causing the wipers to stay on. Try moving the switch back and forth a few times to see if that resolves the issue.
2. Inspect the wiper motor relay: The wiper motor relay controls the power supply to the wiper motor. If the relay gets stuck or fails, it can cause the wipers to stay on. Locate the wiper motor relay in the fuse box or relay panel and try replacing it with a known working relay of the same type to see if that resolves the issue.
3. Check the wiper motor circuit: The wiper motor circuit may have a short or an electrical problem that is keeping the wipers engaged. Inspect the wiring harness connected to the wiper motor for any signs of damage or loose connections. Use a multimeter to check for continuity and proper voltage in the circuit. If you are not familiar with automotive electrical systems, it is advisable to consult a professional technician or a qualified electrician.
4. Disconnect the battery: As a temporary solution, you can disconnect the negative terminal of the car battery to stop the wipers from running. This will disable other electrical components as well, so it's recommended as a temporary measure until the issue can be properly diagnosed and repaired.

Question edited for clarity. Part of duplicate question added.
Duplicate question deleted.
Question moved to model category.

This says Pulse Board or the Switch

https://www.google.com/search?q=2004+Pontiac+Montana+front+wipers+won%27t+turn+off

This says it does have a relay... but

https://www.google.com/search?q=2004+Pontiac+Montana+wiper+relay

Nothing shows where it is located.

https://www.google.com/search?q=2004+Pontiac+Montana+wiper+relay+location

Relay here

https://www.autozone.com/electrical-and-lighting/wiper-motor-relay

It may not be releasing, you can test if you can find it!

https://www.autozone.com/electrical-and-lighting/wiper-motor-relay

..

Your windshield wiper's are computer controlled by the BCM - body control module . The wiper switch is an input to the BCM , which energizes two different relay's to turn on the wiper's . Taking the vehicle to a qualied repair shop an having diagnostic's run would be your best bet , unless you have a professional scanner that can read DTC'S - diagnostric trouble code's in the BCM !
DTC B3715 00: Front Wiper Relay Drive Circuit
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
This is always the first step in the diagnostic process . An if you do not know how they work ,reading factory service manual info. should be done .
Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
Your best bet , take it to a qualified repair shop.

First you need a wiring diagram, free at http://www.bbbind.com/free_tsb.html Then you need a DVOM - digital volt ohm meter to test the circuit . Then if your not familiar with automotive electrical systems testing ,go on youtube an check out Electric Testing Techniques You Need to Know Also having a factory diagnostic trouble shooting chart would also be usefull . You could just start replacing parts , you mite get lucky . The wiper motor is a high fail part , so is the switch ..You could find the fuse is blown ! But fuse's don't usually blow without a reason . Short to ground , low resistance . ( high current flow) Also knowing how they work and what all is involved in making them work.
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Windshield wiper motor module
• Windshield wiper motor
• Windshield washer pump motor
• FRT/WPR/WSHR 25A fuse

Wiper/Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls wiper motor operation. The windshield wiper motor is a 2 speed motor and is operated at low speed in all modes except HIGH. The accessory voltage supply circuit to the windshield wiper motor assembly is used to operate the wiper motor in all of the low speed modes. The accessory voltage supply circuit to the windshield wiper/washer switch is used to supply the windshield wiper switch signal circuits and the wiper motor high speed circuit.
When the wiper/washer switch is in the LOW position voltage is supplied through a 24K ohm resistor within the switch to the windshield wiper switch signal 2 circuit, and accessory voltage is supplied to the windshield wiper switch signal 1 circuit. The reduced voltage from the wiper switch signal 2 circuit and accessory voltage from the wiper switch signal 1 circuit causes the wiper motor module to close the wiper motor accessory voltage supply circuit to the wiper motor low speed terminal.
Windshield wiper/washer system MIST operation is identical to LOW operation except that the MIST switch is a press and release type. When the wiper switch is moved to the MIST position and released, low speed wiper motor operation is started and will continue until 1 cycle is complete. If the wiper switch is moved to the MIST position and held, the windshield wiper motor will operate in the LOW mode until the switch is released.

Don't the wipers work in any mode ?
1
Did you review the Wiper/Washer System description and operation and perform the necessary inspections?
YES - Go to Step 2
NO - Go to Symptoms - Wiper/Washer Systems
2
Turn ON the ignition , with the engine OFF.
Operate the windshield wiper/washer switch through all the switch positions.
Does the windshield wiper/washer system operate normally?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn OFF the ignition.
Disconnect the harness connector of the windshield wiper motor.
Turn the ignition ON, with the engine OFF.
Connect a test lamp from the accessory voltage circuit of the windshield wiper motor to a good ground.
Does the test lamp illuminate?
YES - Go to Step 4
NO - Go to Step 13
4
Connect a test lamp from the accessory voltage circuit to the ground circuit of the windshield wiper motor.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 14
5
Connect a test lamp from the signal 2 circuit of the windshield wiper switch to a good ground.
Press the windshield washer switch.
Does the test lamp illuminate?
YES - Go to Step 11
NO - Go to Step 6
Let me know if you make it this far and i will send rest of diagnostic's

This is a complex wiper system . Here are all the components involved !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch

?€¢
Body control module (BCM)

?€¢
Wiper 1 relay

?€¢
Wiper 2 relay

?€¢
Wiper diode

?€¢
Windshield wiper motor

?€¢
Windshield washer pump

?€¢
Windshield washer nozzles

?€¢
Windshield washer solvent container

?€¢
Windshield wiper arm and blade assemblies

?€¢
Windshield wiper transmission

?€¢
WIPER/SW 10A fuse

?€¢
WIPER 25A fuse

Circuit/System Description
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation. The windshield wiper motor park operation is controlled by the BCM. The BCM recieves an input from the park switch to determine wiper blade position. When the wiper blades are at the bottom of the windshield glass in park position the wiper park switch will open and the circuit will be pulled up to B+ by the BCM. The park signal will be pulled to ground by the wiper motor park switch while the wiper blades are not in the park position.
The BCM controls the windshield wiper motor through two output controls, controlling two relays which determine the desired wiper speed, high or low
Diagnostic Trouble Codes (DTCs)
The body control module (BCM) monitors the voltage on the windshield wiper switch signal 2 circuit for diagnostic purposes. If the circuit is shorted to voltage while the driver is commanded OFF, the BCM will store DTC B3715. If the circuit is shorted to ground while the driver is commanded ON, the BCM will store DTC B3715. Refer to DTC B3715.
It would be best to have a factory scan tool to diagnose this problem . it would make it easier anyway .
It

It is located on the fuse panel on the Passenger side.
Look for the removable panel that is located below the radio/center bezel on the right side (passenger side). It's not part of the center shifter console, but just forward of it. Remove the panel marked "Fuses"! You will find the Wiper Fuse in this panel along with the fuses for the Radio, Accessory Power Plug/Lighter, Power Door Lock & Window Relays, Fuel Pump Relay, Cruise Control fuse, exc......
Hope this info helps!

Could be anything but based on experience the probability points to the self cancelling switching in the motor gearbox.

could be , probably is the speedometer cable, should be fairly cheap repair

Wiper Motor Switch Troubleshooting Check out someother GM wiper fail's video's ,not shuting off means the park switch is bad inside the motor assembly ,u need a new motor .

no this is not an expensive problem. you just need the wiper relay switch.