Question about 1994 Jeep Grand Cherokee

2 Answers

Need to replace signal light flasher can not find old one

Posted by catfishhudy on

Ad

2 Answers

Alexander Mimun

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Front seat area, driver side, under dash, driver side of steering column mounted in convenience center.

Posted on Jul 02, 2010

Ad

ZJ Limited

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

The turn signal flasher and hazard units are usually located located under the dash either to the left or right of the steering column on most models:

  1. Remove the turn signal flasher unit or hazard unit by pulling them up from the electrical connection.
  2. To install, push the unit(s) into the electrical connector.
Also, I suggest check your repair manual in this link: Jeep ZJ-Secc-8W-Wiring-Diagrams

Hope helps (remember rated this).

Posted on Jul 02, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced my tail/ turn signals in my 1997 olds Aurora with led lights. The turn signals don't flash but the hazard lights blinks. What's the problem?


I would suspect that it has something to do with the flasher unit. They operate based on current draw heating up a bimetal piece that causes the blinking. Four-ways (hazards) draw more current since there are more filments/LEDs drawing current. By changing from incandescent to LED you have reduced the current draw on the flasher. You may need a different flasher that uses lower current to get turn signals to work. Here is a link that explains it and provides info on how to get the proper flasher.


LED Turn Signal Bulbs Flashing Problems

Oct 06, 2015 | Cars & Trucks

2 Answers

1967 GMC 2500 brake lights flash on and off except when blinkers are turned on. How do I fix it ?


Sounds like you need a new turn signal switch. And a new flasher relay, just in case your old one got overused! Those little flasher relay cylinders were real cheap back in the day, about $2. It's under the dash around the steering column, probably in a little metal clip (yea, real metal). Don't confuse it with the hazards flasher, both look the same. You can hear and feel the turn blinker flasher when it is doing its thing, and same with the hazards flasher, if you want to check. The clicking is the make and break contact of the circuit to cause a blinking bulb.

The reason I say you need a new turn signal switch is because the brake light signal wire is routed through the turn signal switch before it goes to the rear brake light bulbs. It is inside the turn signal switch that the brakes and rear turn signal lights are made to share the same filaments inside the bulbs. The brake lights don't pass through the flasher, but somehow your turn switch is sending power to the flasher. If the wiring under your dash has not been radically altered, really messed up, then your turn signal switch has got infected with a malware virus: it is worn out and needs replacing. Good luck with that old piece of iron, Greg.

Apr 09, 2015 | GMC Cars & Trucks

1 Answer

Turn lights blink with hazards but not with turn signal..flasher replaced. is It the multifunction lever then??


There should be a turn signal flasher and a hazard flasher. They are two different parts. If you replaced the hazard flasher and not the turn signal flasher than I would start by replacing the turn signal flasher.

One thing you can do once you find the turn signal flasher is to unplug it and use a jumper wire between the two pins of the connector then turn the key to the run position and place the turn signal lever in the left or right position. If the turn signal lights know light up than the turn signal flasher is the problem

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Sep 09, 2014 | 1997 Oldsmobile Cutlass Supreme

1 Answer

My blinkers are not working.I replaced fuses and flasher.My hazard lights work but my blinkers still dont.What else could I check.


are you sure you replaced the signal flasher and not the hazard flasher as they look the same.put the hazards on and check to see if it was the one you replaced.if it is then you need to located the signal flasher and replace it.if you still have the old one you replaced you can use it.

May 01, 2011 | 1997 Ford Thunderbird LX

2 Answers

My hazard lights flash but my left / right turning lights do not blink. Where do I find the flasher to replace it? 1995 olds 88


if the hazards flash the problem is not the flasher. Most likley you need a turn signal switch

Oct 16, 2010 | 1989 Oldsmobile Delta 88

3 Answers

97 olds 88, left turn signal not blinking.


possibly one side of your signal flasher is out turn on emergency flashers to locate one flasher then you can locate the other

Sep 12, 2009 | 1997 Oldsmobile 88

2 Answers

Flasher clicks turn signals all work. What needs to be replaced? 2004 Pontiac grand am gt


The clicking noise is you concern ? I would replace the turnsignal switch or the hazzard switch.

Good Luck

Aug 16, 2009 | 2004 Pontiac Grand Am

2 Answers

Need loud signal flasher for 2008 Toyota RAV4


the module can be replaced by a chime or a truck blinker switch from a diesel truck shop and you may here it, however the other guy is right and has a couple good ideals. JC whitnet has one
here is the web page. and this is for the
RAV 4 http://www.jcwhitney.com/autoparts/Search?catalogId=10101&storeId=10101&sku=loud+turn+signal+flasher
g_13364g_th_1.gif;pv2b80a320e50f7422 CEC INDUSTRIES MUSICAL AND VERY LOUD TURN SIGNAL FLASHERS
Hear your turn signal over road noise and music! Select "Love Me Tender" which plays at standard volume, or our signal flasher louder than a standard flasher.
Review this product

Jun 26, 2009 | 1999 Toyota RAV4

1 Answer

All signal lights do not flash on outside of 1994 olds silhouette


There is a turn signal flasher on your fusebox it should either be round or say flasher control on it and if your replace this your flashers should work fine. I hope you have good luck!

May 20, 2009 | 1994 Oldsmobile Silhouette

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...