Question about 1994 Toyota Corolla

1 Answer

What is the SPARK PLUG socket size for Toyota Corolla 1994 1.6 liter, please?

Posted by jhorsman04 on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 3 Answers

Hi there, For your 1994 Toyota Corolla 1.6L engine, you will need a BOSCH premium class Platinumir fusion spark plug.  It is an Iridium platinum spark plug.
Its dimensions are a 14mm thread, a 19mm reach, and a 16 mm hex size.
I hope this will be of help to you.
Do remember to rate this answer.

Posted on Jun 30, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change spark plugs toyota corolla 2002


First you will need the correct size spark plug socket and a longer extension bar for it. Most sets are not expensive to buy.
ONLY REMOVE ONE PLUG LEAD AT A TIME!!!
Make sure there is no loose dirt on the area your working.
Using it's cap, (not the wire), pull out the first plug lead. Insert the socket and gently push into place. Plug sockets have a rubber insert fitted to grip the plug as you lift it out. Using firm (but not rough) pressure, unscrew the old plug.
For the new plug, REMOVE the ratchet and insert the plug into the socket using the rubber insert to hold it in place. Lower the plug into place and GENTLY screw it into place, using the extension bar like a screwdriver. If you hit resistance unscrew and try again. A stripped screw thread is VERY expensive to fix. Tighten the plug to 35Nm (25ft/lb). REFIT the plug lead BEFORE moving to the next spark plug.
Repeat for each spark plug in sequence.

Jan 10, 2018 | Toyota Cars & Trucks

Tip

Toyota Highlander_ How to change plugs


The Toyota Highlander is available in three different engine sizes: 2.4, 3.0 and 3.3 liter. The basic technique for replacing spark plugs is used for both engine sizes, but depending on the engine size you need to remove different parts from the Toyota Highlander to gain access to the spark plugs.
  1. 1 Pull the hood release and raise the hood on the Highlander. Allow the engine plenty of time to cool.
  2. 2 Remove some components to reach the spark plugs. On a 3.3 liter engine, unscrew and remove the V-bank cover and intake air tank. On a 2.4 and 3.0 liter engine, remove the number one engine cover.
  3. 3 Locate the ignition coils and spark plug wires that connect directly to the spark plugs or directly to the engine in the Toyota Highlander. In 2001 and 2002 models, theses are on the front and back of the engine. On models made after 2002, the spark plugs are along the sides. Grab the ignition coils or spark plug wires by the thick plastic piece at the end of the wire. Squeeze the end and turn it to release it from the spark plug. Pull back to remove the plug from the engine.
  4. 4 Slide the spark plug socket over the spark plug. The most common size of spark plug socket used on a Toyota Highlander is 16mm. Turn the socket to the left to unscrew and remove the spark plug from the cylinder well.
  5. 5 Apply a thin coat of anti-seize compound to the spark plug thread and into the wire boot to reduce the chance of sticking.
  6. 6 Insert the spark plug into the well and manually turn the plug into place. If you cannot reach the plug well manually, insert the plug into the socket and extension and use the extension to turn the plug into place. Do not use a socket wrench or flexible extension for this process because their force damages the spark plug.
  7. 7 Connect the ignition coil or spark plug wire to the spark plug. Turn to lock it into place.
  8. 8 Continue this process for the rest of the spark plugs. Replace any removed items onto the engine and lower the hood.



on Jan 26, 2011 | Toyota Highlander Cars & Trucks

2 Answers

How do I check for spark in my 1994 toyota corolla. I have volt/ohm/amp meters if necessary.


Disconnect a spark plug wire ... attach a plug to it ... turn the engine over ... watch the plug ... spark?

Apr 29, 2011 | 1994 Toyota Corolla

1 Answer

Anyone have picture/illustration of where the spark plug are located on a 2005 highlander?


  1. 1 Pull the hood release and raise the hood on the Highlander. Allow the engine plenty of time to cool.
  2. 2 Remove some components to reach the spark plugs. On a 3.3 liter engine, unscrew and remove the V-bank cover and intake air tank. On a 2.4 and 3.0 liter engine, remove the number one engine cover.
  3. 3 Locate the ignition coils and spark plug wires that connect directly to the spark plugs or directly to the engine in the Toyota Highlander. In 2001 and 2002 models, theses are on the front and back of the engine. On models made after 2002, the spark plugs are along the sides. Grab the ignition coils or spark plug wires by the thick plastic piece at the end of the wire. Squeeze the end and turn it to release it from the spark plug. Pull back to remove the plug from the engine.
  4. 4 Slide the spark plug socket over the spark plug. The most common size of spark plug socket used on a Toyota Highlander is 16mm. Turn the socket to the left to unscrew and remove the spark plug from the cylinder well.
  5. 5 Apply a thin coat of anti-seize compound to the spark plug thread and into the wire boot to reduce the chance of sticking.
  6. 6 Insert the spark plug into the well and manually turn the plug into place. If you cannot reach the plug well manually, insert the plug into the socket and extension and use the extension to turn the plug into place. Do not use a socket wrench or flexible extension for this process because their force damages the spark plug.
  7. 7 Connect the ignition coil or spark plug wire to the spark plug. Turn to lock it into place.
  8. 8 Continue this process for the rest of the spark plugs. Replace any removed items onto the engine and lower the hood.

Read more: How to Replace Spark Plugs in a Toyota Highlander ' eHow.com http://www.ehow.com/how_4484644_replace-spark-plugs-toyota-highlander.html#ixzz1C6Y4k5y2

Jan 26, 2011 | 2005 Toyota Highlander

1 Answer

What are spark plug torque specs for 2003 toyota corolla


Toyota do not have a specific torque setting for spark plugs in the master workshop manual,they say "hand tight, plus 1/8th turn"(using a plug socket and ratchet handle).

Oct 31, 2010 | 2003 Toyota Corolla

2 Answers

Car is making funny noises and wont accelerate


I had this problem also after i washed my car engine compartment, water in spark plug compartment causes this problem. remove the wire plugs from the spark plugs and dry the compartment/spark plug sockets, also open the air filter compartment and make sure it's dry and clean. also do not forget to inspect your spark plugs also, install new ones and your car will run like new! Good Luck

Feb 08, 2010 | 1994 Toyota Corolla

1 Answer

How do you change the spark plugs on a 1998 toyota corolla?


pop the spark plug wires out of the engine, get a pretty long extension and the right size socket, and untwist them out, replace, (make sure if the new plugs need to be gapped, you do so properly, this will save you on mpg and spark plug life) and put it back together making sure you put the wires back in the same order you took them out! Good luck and please rate me!

Oct 12, 2009 | 1998 Toyota Corolla

2 Answers

I need advice on how to get the old plugs out of my 2007 Toyota corolla. I removed the coils and when I tried to put the socket in the plastic tube that houses the coil unit I could not get the spark plugs...


those rubber sealt are for the end of the spark plug boot you can take a long screw driver or long needle nose pliers and remove them gently then you can get your socket onto the plugs for removal

Apr 20, 2009 | 2007 Toyota Corolla

1 Answer

Spark Plugs


first open the hood and if you look at the engine theres is a black cover, there are two nuts on the bottom and you need a size 10mm socket if im not mistaken, take those off and on the top corner of the black cover there are two little plastic things that you just pop up with a flat screw driver. once all that is taken off pull the black cover up and put it aside. now you can see the 4 ignition coils because it dosent have spark plug wires. to get to the sparkplugs you need to take out the ignition coil. you need to remove the screw it is a 10mm socket i think and once you remove the screw disconect what ever its conected to and just give it a twist and pull it up and if you peak in the hole the spark plug will be right there.

Aug 05, 2008 | 2000 Toyota Corolla

Not finding what you are looking for?
1994 Toyota Corolla Logo

1,326 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...