Can bearings be chaaged on front wheel hub of chevy 2000 suburban 2 wheel drive

no you unbolt the hub and replace as a whole unit
Front wheel bearing and hub replacement on 2001 Chevrolet Malibu By Tejvir this is what they look like
2000 CHEVROLET MALIBU 3 1L V6 Wheel Bearing Hub Assembly RockAuto

Chevrolet Suburban Questions - 4 wheel drive does not ...

www.cargurus.com > Questions > Chevrolet > Suburban

CarGurus4 wheel drive does not work - When I put the Sub in 4 wheel drive, low of high, ...Asked by Robert_Holland_073 Dec 17, 2009 at 04:06 AM about the 1994 Chevrolet Suburban K1500 4WD ... it can seize up and then the trans case may ingage but the hubs won't be locked in so it ... 1999 Chevrolet Suburban K2500 LT 4WD.

Chevrolet Tahoe Suburban 4 Wheel Drive Indicator Lights - Car ...

forums.edmunds.com > Chevrolet > Chevrolet Suburban

Oct 2, 2007 - 31 posts - ‎19 authors
My 1999 Tahoe (odo reading 137,400 miles) won't go into 4 wheel drive. .... I have a 98 suburban 1500 4x4 LT 5.7 L with 165,000 miles ... I recall once forgetting todisengage 4WD and I could feel a terrific binding when I ...
Step by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC ...? 21:32https://www.youtube.com/watch?v=Su9Dkrfd_ZgJan 20, 2014 - Uploaded by rwdellingStep by Step Troubleshooting 4wd 4x4 88-98 Chevy GMC Truck. rwdelling .... Mine is acting like it is NOT pulling with the fronts,won't engage. ... Have you ever adjusted or the shift cable on your 1500 Chevy ... GM 246 transfer case, 2000 Chev Suburban- Duration: 20:09. by spelunkerd 286,045 views.GM Troubleshooting Part 13 - 4WD vacuum actuator & cable ...? 5:11https://www.youtube.com/watch?v=CbEF6PyJdU0Feb 3, 2011 - Uploaded by mr diyguy123I tacked on this video about the 4wd sys. ... I have a 1994 ChevyS10 ... My S10 won't let you go to 4 LO when your in gear. ... the front end to keep them disengaged. when you put it in 4wd, the vacuum actuator pushes a gear ...

about 80 lbs is sufficient ,if the wheel still can moved top to bottom then then renew the bearing ,and check the ball joints on the lower track control arm

old post, but you are first to say front. many others fail to say end of car.

is your car 4wd, as 2wd is different rules. so...??????

I toss coin land on 4WD.

2000 front wheel bearing

got it.

the 2000 year, is important.

this year is the last year, before non untized hubs.

http://www.fixkick.com/hubs/FW_BEARINGS.html#newer



my posts is for stock cars. only, and USA spec, cars.

other countries, evolve this in different years.



2000 (never 2001+)

fsm quotes

1. Before servicing the vehicle, refer to the Precautions section.



2. Remove or disconnect the following:
   
   
   
   
   
   • Front wheel
   
   
   
   • Brake caliper and rotor
   
   
   
   • Locking hub or hub drive flange, if equipped,(it is)
   
   
   
   • Hub grease cap, if equipped
   
   
   
   • Wheel speed sensor, if equipped (ABS)
   
   
   
   • Wheel bearing lockwasher
   
   
   
   • Wheel bearing locknut (ring) and inner washer
   
   
   
   • Wheel hub and bearing assembly (slide hammer?)
   
   
   
   • Wheel hub oil seal
   
   
   
   • Wheel bearing oil seal
   
   
   
   • Snapring
   
   
   
   



3. Press the wheel bearing and race out of the hub.

reverse is same but the lock ring must be set

to 123-180PSI. stop tightening above 123 at first alignment hole in lock ring..

You cant grind it off then get new one.

Mai Lor

If it's 4 wheel drive, it could be a bearing in the differential or transfer case chain on its way out.

If it's 2 wheel drive then all it could be is either brakes or wheel bearing/hub assembly.

Sounds like there may be a problem with the left front wheel bearing/hub assembly easy to replace only takes about 30-45 min and about $55-125 in parts. Jack both front whels up and with it in drive turn wheels back and forth and listen to each side. I am pretty sure it is the left side but check both.

Check the wire harness on the transfer case to make sure it's still plugged in. Check the selector switch in the dash. Check the hub sensor wire harnesses on the front wheels.
Check for error codes through OBD-II connector under the dash.
Good luck.

check bearings