How do I open the soft top on a merceedes 320 sl and move the wing mirrors

Question edited for clarity and toss in some CAPS.
Question moved to model category.

Exterior Mirror Replacement Glass for CITROEN C2 (2003 ...

Amazon.ca https://www.amazon.ca > Exterior-Replacement-CITR...

1.Remove all existing mirror glass from the mirror assembly plastic backing plate. 2.Clean the backing plate with rubbing alcohol and clean the back of the new ...
$70.50 · ‎In stock

Car Wing Heated Mirror Glass Lens, for Citroen C3 ...

Amazon.ca https://www.amazon.ca > Heated-Mirror-Glass-Citroen...

Easy to install: The damaged mirror can be replaced directly, and an alternative to replace the entire mirror housing is provided. If you have any questions, ...
$69.05

Low Price Guarantee on citroen c3 picasso Wing Mirror ...

Car Door Mirrors https://www.cardoormirrors.com > citroen > c3-picass...
Low Price Guarantee and Free Delivery on High Quality citroen c3 picasso Wing Mirror Glass, Replacement citroen c3 picasso Wing Mirrors and Stick on Mirror ...
£4.99 Videos
..

buy a new on , and swap em./

Quit SHOUTING will ya :>D Typing in all CAPS is considered SHOUTING in Internet land. It also make the text VERY HARD TO READ.

You need a good, local auto electrician with a pro-grade scan tool computer. You have a faulty module probably Body Control Module, or Security System Module, the sensors and receivers connected to them, or a general communication issue.

Hi Michelle , what make model an year vehicle ? On some vehicles this is function is controlled by a door module .

In order to control outside rearview mirror operations, as well as other door functions, the front door modules must be powered up. For this purpose, battery voltage is supplied from the rear fuse block, through separate circuits, to each front door module. Each front door module is separately grounded through a ground stake. The front door modules also use these power and ground supplies to drive the mirror motors, and to provide power and ground to window and lock switches and door lock actuators. In addition, the driver door module (DDM) uses these power and ground supplies to power the driver door switch assembly (DDSA) and integral mirror control switches.
Could have DTC'S - diagnostic trouble codes stored in BCM - body control module .
DTC B1544 01: Mirror Motors Common Circuit Short to Voltage
DTC B1544 02: Mirror Motors Common Circuit Short to Ground
DTC B1544 04: Mirror Motors Common Circuit Open Circuit
DTC B1600 01: Mirror Motor 1 (vertical) Circuit Short to Voltage
DTC B1600 02: Mirror Motor 1 (vertical) Circuit Short to Ground
DTC B1600 04: Mirror Motor 1 (vertical) Circuit Open Circuit
DTC B1605 01: Mirror Motor 2 (horizontal) Circuit Short to Voltage
DTC B1605 02: Mirror Motor 2 (horizontal) Circuit Short to Ground
DTC B1605 04: Mirror Motor 2 (horizontal) Circuit Open Circuit .

probably just rusty try spraying releasing fluid in it move the mirror as the button is being pressed or the motor and gearing is going

yes there is a manual release for the locks. Hopefully you still have the tool kit with the soft top tool in it. It will have a open wrench on one side and a allen on the other. For the rear locks use the open end wrench side and behind the side trunk panels you can see the mechanism for the rear latches. Slide the tool over the release mechanism and move upwards while lifting up on the top. For the front latches swing the visors to the side and remove little round cover. Insert allen side of tool and rotate until latch unlocks. Make sure vehicle is running when ever you operate the top or hard top as voltage can affect the operation of the latches.

Best to take it to a shop or a delaer to get codes, but I think the top latch above the rear view mirror is not clamping down the top tight enough. The second message "Check Soft Top Motion" leads me to believe this - the OBD thinks the top hasn't finished opening/closing. Unfortunately there isn't too much in the way of adjustment that can be done, besides R&R of the microswitches (that you mention are in good shape).

Check this guide as reference for solve ypur problem; this is one DIY about replace Wing Mirror...
1.- Disconnect your negative battery cable, if your Ford Focus has power side mirrors. If it has manual side mirrors, disconnecting the battery is unnecessary.
2.- Pry off the wing mirror's inside sail panel (shaped like a triangle). Insert a trim panel tool between the door skin and the plastic panel to pry it off.
3.- Carefully pull the sail panel away, minding the wiring if the mirror is power-operated. Unplug the electrical harness and set the panel aside.
4.- Open the door and hold the outside part of the wing mirror steady. Remove the mounting bolt with a socket wrench, and then remove the mirror screw with a Phillips screwdriver (the mirror bolt and screw is visible with the panel removed).
5.- Pull the wing mirror assembly from its mount (from the outside). Insert the replacement mirror assembly in place; tighten the bolt and the screw.
6.- Attach the wiring connection to the replacement mirror. Position the sail panel in place and push it against the door to snap it back on.

Hope helps (remember comment and rated this). TY for using Fixya.

Car must be on a level surface. Make sure hydraulic system is full and pistons dont leak and go from there.

Sounds like you are probably low on fluid. Check for leaks and fill system. Also make sure car is level. I also suggest you get an owners manual as all of it is covered by the book.