How to fix my front driver strut

Replace the fan relays. The Radiator Cooling Fan Motor Relay is located: Under hood, driver side, front side of strut tower, mounted in relay panel
Application:
High speed The Radiator Cooling Fan Motor Relay is located: Under hood, driver side, front side of strut tower, mounted in relay panel
Application:
Low speed,here's a new part.
http://www.autozone.com/cooling-heating-and-climate-control/relay-radiator-cooling-fan-motor/duralast-relay-radiator-cooling-fan-motor/plymouth/voyager-2wd/1996/6-cylinders-3-3-0l-mfi/412240_0_0

No,they won't change out and you have to use a left for the left side,right for right side.

1992 Toyota Celica is not equipped with front "shocks". This vehicle is equipped with front wheel drive and independent MacPherson strut front suspension. Any repairs made to this system requires the removal of the entire strut assembly, which includes the strut, the coil spring and upper strut bearing assembly.

Replacement of any of the parts of the strut assembly requires the use of specialized equipment designed to compress and hold the coil spring to relieve the tension on the strut and upper bearing assembly.




Any attempt to disassemble the strut assembly without the proper equipment for compressing and securely holding the coil spring can result in SERIOUS INJURY or DEATH.

it sound like the strut bushing is gone must change

The struts model (MacPherson Strut),are both in front and back of this car.
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly. $72
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $68
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $67
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $63
Of course this is only the cartridge, you have to transfer the spring, and the top mount of the existing strut. You need a pair of coil spring compressor to do the job. The basic procedure to replace a strut is:
Remove the top nuts that secure the strut assembly to the frame mount inside the engine compartment. Do not remove the center nut.
Mark the lower strut mounting location on the hub for installation reference. The alignment will be close if the new strut is installed in the same position.
Remove the bolts that hold the strut assembly to the hub.
Remove the strut assembly from the vehicle.
Mark the top mount for installation reference. Using a side mounted spring compressor, compress the spring and remove the top nut and retaining washer. Pull strut assembly out from the bottom of spring.
Slide the new strut assembly up into the spring and reposition the top mount onto the spring in the same position that it was removed. Install the retaining washer and top nut.
Tighten the top nut to the manufacturer's specifications and carefully remove the spring compressor.
Place the strut assembly back into the vehicle.

Hello tunamae: My name is Roger and I will help. Your 1993 Voyager has struts on the front of the vehicle. In order to change them you will need special strut tool in order to change the strut springs form the old struts to the new ones. Should you need further help please just ask.Please rate the answer you received as this way I know it was helpful. Thank You for using Fix Ya, Roger

See if you can bounce car and replicate the noise. If you can, you should be able to find it, and put your hand on it. Stabilizer bushing are a place to look, both at the lower a arm and on the frame. If you narrow it down to the strut, it will need to be replaced. The front trans mount also goes bad, try putting it in drive with your foot on the brake and give it some gas and see if the engine moves an excessive amount.

A: Use two jack-stands under the front-frame rails, a hydraulic jack under the "bulb" in the control-arm and a third jack-stand under the "spindle extension" of the rotor. It's not necessary to remove the calipers and/or rotors. The upper strut-mounts might need to be forcibly loosened and then removed. If the old struts are worn out enough, they should just compress by themselves. The new struts should be able to be compressed by hand and then positioned in place as fast as possible, before they extend.
For the strut-to-knuckle bolts to loosen, use a pipe extension to the fixed driver of the socket-set. To tighten these bolts, first torque them to 170 Nm and then give them an additional turn of 120 degrees. For the latter, use the pipe-extension again

If your car has over 75K miles on and the struts are original, I'd have the struts replaced. As for the coil spring, you can probably find a repair manual at your local library. You can get loaner spring and strut compressor tools at most auto parts stores (loaners are free, just have to leave a deposit for the price of the tool).

Repair cost will vary from place to place, but I'd say coil and strut replacement is about 4-5 hours labor. I'd guess a $300-$450 for parts and labor (coil - $100, pair struts - $140)

Jack up and secure front end of your vehicle,Take off two front wheels. Loosen to bolt on the bottom of struts (Its a bolt and nut). Remove clip that holds brake hose on to strut and remove hose. DO NOT OPEN BRAKE LINE OR DISCONNECT FROM CALIPER. Remove bolts and remove bottom of strut from knuckle/Hub assembly. Then loosen nuts on strut tower( on top of fender inside hood) (3) nuts, mark exact locations of each nut on strut mount area on upper fender weld. Make sure to hold strut on the bottom so it doesn't drop down on caliper and knuckle or on you possibly.YOU WILL NEED A SPRING COMPRESSOR to compress spring so you can take struts off. MAKE SURE THAT SPRING IN COMPRESSED/SQUEEZED WITH A STRUT COMPRESSOR. Then loose center nut on strut tower(may be covered with a circular rubber cover) If nut spin around with out getting loose use vise grips to hold strut rod ONLY TO REMOVE STRUT NOT TO INSTALL. if you use vise grips to install it will damage strut. When nut is off, remove strut and reinstall new one transfer all rubber boots and cushions from old strut. Good Luck thanks for using FIX-YA.com contact me if you need more help.