SOURCE: Daewoo Leganza 2000 timing belt broke
there are no manual at napa or any where else except dealer. they want 100+ dollars for one in MI.
SOURCE: Need Instructions on removing and replacing a fuel pump for my 2000 daewoo leganza
Hello martin09canc: First thing to do is relieve fuel pressure in the fuel system. Remove the rear seat cushion.Remove the access cover. Disconnect the electrical plug.Would not hurt to disconnect the negative battery cable. This would eliminate any sparks. Remove the sender retaining ring. Lift out the sender unit. Be careful not to spill gas on the carpet. Replace the seal and reverse the operation to install new unit. If you need further help please just ask. Please rate the quality of the answer as it also helps. Thank You for using FixYa. Roger
SOURCE: how to change a timing belt on a 2000 DAEWOO
Follow these instructions to the letter, if u get this wrong u will bend the valves in the engine.
Required tools:
13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers
If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.
Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.
To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponding line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple.
In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long.
One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it
SOURCE: free owner manual for 2000 daewoo leganza
you can download the manual by searching online for auto manuals. The download I used was like 48 pages of information, all free of course.
SOURCE: unlock radio codes for 2001 daewoo leganza
Usually daewoo prints the code on a sticker on top of the radio. Pull off the dash cover and look it to see if you can see the code. Or pull out the radio and see if it is there.
133 views
Usually answered in minutes!
×