Question about 2000 Dodge Intrepid

How to change cam positiom sensor in 2000 dodge

How to change cam position sensor in a 2000 dodge intrepid and where is it located

1 Answer

Anonymous

Level 1:

An expert who has achieved level 1.

Hot-Shot:

An expert who has answered 20 questions.

Corporal:

An expert that has over 10 points.

Mayor:

An expert whose answer got voted for 2 times.
Contributor
31 Answers

The cam position sensor on the 2.7 engine is on the
driver side of your engine, right in the front of the head. there's a 10mm bolt. undo the bolt and pull it straight out. push the new one into the hole, and hold pressure on it until it's bolted back in.

If you have the 3.5, the cam position sensor is located on top of the timing cover. I just unbolt the upper intake just enough to lift it up a little. unbolt the cam sensor, pull it out and install the new one keeping pressure on it until it's bolted in.

I hope this helps

Posted on Aug 07, 2010

Add Your Answer

Upload

Upload an image from your computer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

Loading...

Include an image. It's worth a thousand words.

prev next

Related Questions:

1 Answer

My dodge intrepid 2000 will not start. When it went out it felt as if i ran out of gas almost. Although i have a full tank, I had my camshaft sensor located on the front mid of the block changed, that is...

Hello
Sorry to note that problem with cars are not related with my expetise. OK.

Nov 06, 2011 | 2000 Dodge Intrepid

1 Answer

I need to know the exact location of the camshaft position sensor in my 2000 dodge intrepid. 2.7L. All the answers I find are very vague to me :-(

The Camshaft Position Sensor is mounted in the front of the timing case cover.

May 27, 2011 | 2000 Dodge Intrepid

1 Answer

I have a 2001 dodge intrepid. I just replaced the output speed sensor. It is still stuck in limp in mode.

There is a recall on some intrepids for the cam position sensor. You may have to change the cam sensor, if you don't have a code for it, don't change it. You might have to go to the dealer and have them flash your computer with a scan tool. that may be covered under the recall. I would investigate if I were you.

I hope this helps

Aug 06, 2010 | 1998 Dodge Intrepid

2 Answers

Code p0340 on 2000 dodge intrepid

it might be the cam shaft sensor it might be the crank shaft sensor the best thing to do is replace them bolth. but it does sound like it may be either one because if one goes out the other will still work but when starting the car it will take longer for it to read from either or the one sensor that is still working because they work together to tell the system to deliver the gas. im pretty positive that it is either the cam or crank shaft sensor

Jun 21, 2010 | 2000 Dodge Intrepid

1 Answer

Replacement of cam position sensor

driver side front of engine

Apr 17, 2010 | 2000 Dodge Intrepid

1 Answer

Locate cam position sensor on 2004 dodge intrepid

The camshaft position sensor is mounted to the top of the timing case cover.

Oct 25, 2009 | 2004 Dodge Intrepid

2 Answers

Where is the camshaft position sensor located on a 2000 Dodge Intrepid?

If it is a 3.5 it is located on the front of the engine on the drivers side under the plenum.

Oct 23, 2009 | 2000 Dodge Intrepid

1 Answer

Where is the cam sensor located for 2000 dodge intrepid

As you are looking at the engine, it'as on the right front of the valve cover, very easy to change.

Aug 04, 2009 | 2000 Dodge Intrepid

3 Answers

2002 dodge intrepid starting issue new water pump,new timing chain,new belts, good spart, valves are good Can it be a crankshaft sensor?

dear friend-if you are positive that all the repairs were carried out with great care,that the timing is right,and you got spark and fuel,all the valves close propely,then it should start,if the sensor was ok before you stripped the engine why should it be faulty now.

Jun 29, 2009 | 2000 Dodge Intrepid

1 Answer