I have a 94 dodge shadow es with 2.5 litre. It drove fine till it turned off while driving. I replace the cap rotor wires plugs pick up coil and coil. It has spark to the center coil wire but no spark at plugs. any ideas?
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
I had to replace the magnetic pick-up sensor on the side of the distributor that tells the coil when to fire on my 86 truck. It was $80 and slips onto the distributor held on by the cap.
Had an 84 silverado 305 that did the same thing. Try giving it a full tune up. Plugs, wires... Mine turned out to be fouled plugs. I didn't find that out till after i tore it down & put a timing set in it. Wasn't getting good enough spark.
In reading your issue at hand not having no spark there is only a few things that can cause this being that its a 1988 car i will list below what you need to go over and check.
1.spark plug wires 2. distributor cap 3. ignition rotor 4. coil pick up 5. faulty distributor
That being said most are a easy and cheap fix plug wires run about 20-35 bucks autozonesduralast brand , distributor cap runs between 7-18 bucks , ignition rotor 3-8 bucks , coil pick up about 15-30 bucks all at autozone.
Now there is no real way to tell if there bad but a good examination of the distributor cap and rotor should tell you corroded inside cracked worn down.
i would start with distributor cap , ignition rotor, coil pick up if the car starts after this replace spark plugs wires. If that does not fix it most likely you distributor is faulty itself.
i hope it helps if so could you leave me so 4 thumbs up feedback thanks so much
i would check your distributor cap or just replace it it might have a crack and is not allowing the spark to reach the plug chang the rotor while your at it they shouldnt cost more than 20 together if that doesnt do it have your ignition coil tested
Hi, Hope I can help you. I do not know how you have checked for spark, but lets start from the beginning. Lets start with an ignition systems check. 1. I want you to remove the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Using a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok, If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on. Note if you do not get spark from the coil wire replace the coil.
2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking the rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will allow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor. On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals. If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all. You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage. Once again if you find any damage replace them all. I hope this will help you and good luck to all the read this FixYa
Hi, Hope I can help you. I do not know how you have checked for spark, but lets start from the beginning. Lets start with an ignition systems check. 1. I want you to remove the high voltage coil wire. ( That's the wire in the center of the distributor cap.) Using a good pair of insulated pliers. I want you to hold it about 1/4 inch from a good engine ground. Now you will need a bit of help from a partner. Get them to turn the key and crank the engine. You should see a bright blue and well defined spark. Ok, If you have spark I want you to slowly move the coil wire away from the engine ground. As you do this I want you to pay attention to the coil tower. (The coil tower is where the other end of the coil wire is attached.) What your looking for is arcing and sparking at the coil tower. If this happens then you need to replace the coil with a new one. If this does not happen then your coil is working fine, and we will have to move on. Note if you do not get spark from the coil wire replace the coil.
2. Ok if you have spark now we have find out if the spark is making it to the spark plugs. How are we going to do this? By checking the rotor, distributor cap, spark plug wires and spark plugs.First lets remove the distributor cap. This will allow use to inspected the rotor and the distributor cap. What your looking for is, cracks, carbon tracks and wear at the tip of the rotor. On the distributor ,look inside the cap for cracks, carbon tracks and wear on the terminals. If you find any of this replace the distributor cap and rotor. ( Note if you have any doubt of the condition of the rotor or the cap replace them.) Next lets check your spark plug wires. Lets pull off one of the spark plug wires from the spark plug side. Now inspect the wire connection for a white crusty powder. If you find crust replace your wires. Now you should check all of them the same way, but if even one has corrosion replace them all. You are going to have to inspect the wire its self . Going down the whole length of the wire. Holes cracks burn Marks and other damage. Once again if you find any damage replace them all. I hope this will help you and good luck to all the read this FixYa
How about the pick up coil in the distributor? A trick we used to use back in the day was to tap the distributor housing with a hammer, key word tap. If the engine missed or stalled than the pick-up coil was replaced.
Remove the distributor cap and look to see that the rotor button is turning,and not stopping,the truck,may have jumped time.The timing chain may hve broke.If not,replace the pick up coil in the distributor.
×