Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

Turn signals work off and on seems to be in steering column i dont want to take off steering col i was thinking of cutting wires to switch and patch in new switch on col i need to know if this will work and what colors are wires

Posted by tommarge on

Ad

1 Answer

Anonymous

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

It time for a new turn signals switch

Posted on Apr 17, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazard lights won't turn off


You can not just cut a wire and have the turn signals still work. You need to have the turn signal switch replaced.

Jul 10, 2018 | Pontiac Cars & Trucks

2 Answers

Hi. my low beams in my 97 mustang stopped working and so did my turn signals. i switched out the multifunction switch and that wasnt the problem. any ideas? im thinking bad ground.


If your lights and turn signal are in the steering column u will have to replaced the whole switch

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/jim_c09d8140f32619a8

Jul 15, 2015 | Cars & Trucks

1 Answer

1983 ranger turn signal lights flash quickly on both sides. Hazard lights work. Steering wheel felt locked and heard a breaking sound that seemed to come from the steering column.


fast flashing usually means a bulb is burnt... have you checked them all ??? or did you wire in a trailer plug and did something wrong ???

Dec 28, 2013 | 1983 Ford Ranger

1 Answer

When the key is turned wipers come on, and the right turn signal blinks fast. We think it might be a short in the wires but can't find out where. Is there something else that could be causing the


Technically, the wipers and turn signals are on two different circuits. But its possible the wires have melted together. One place to look would be in the steering col where the wiper switch and turn signal switch come together.
You could try unplugging the harness to see if the wipers still run.

Jan 18, 2013 | 1999 Dodge Stratus

1 Answer

How do I get the part where the plug for turn signal switch go thur this without cut and rewire it?


Take apart the tilt steering column, buy the small harness, and replace.
(Harness has turn signal switch, etc. on one end. Harness goes down the column, and plugs in; on the other end. Or cut wires, solder, and use heat shrink tubing. Slide heat shrink tubing up one wire BEFORE soldering. Slide down onto soldered connection of wire, heat ->heat shrink tubing )

Nov 20, 2012 | Cars & Trucks

1 Answer

How do i install Switch Assembly turn signal Cruise control PART AUTO for a 2002 Impala.


Multifunction Turn Signal Lever Replacement - On Vehicle

Removal Procedure

83422682


  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR system.
  4. Remove the steering wheel.
  5. Remove the steering column trim cover.
  6. Remove the steering column knee bolster.
  7. Remove the steering column wire harness (1) from the steering column wire harness retainer (2).
  8. Remove the 2 wire harness straps from the steering column wire harness (1).
  9. Remove the steering column bulkhead connector from the vehicle wire harness.
  10. Disconnect the connectors from the multifunction turn signal lever steering column bulkhead connector.
85097560




  1. Remove the retaining bolts (1) from the multifunction turn signal lever (2).
  2. Remove the multifunction turn signal lever (2) from the steering column.
Installation Procedure

85097560




  1. Install the multifunction turn signal lever (2). Use a small flat-blade in order to compress the electrical contact and move the multifunction turn signal lever into position.
  2. Verify that the electrical contact rests on the canceling cam.
Notice: Refer to Fastener Notice in Service Precaution.


  1. Install the retaining bolts to the multifunction turn signal lever.
    • Tighten the retaining bolts to 7 Nm (62 inch lbs.) .
92905224




  1. Connect the gray and black connectors to the multifunction turn signal lever steering column bulkhead connector.
  2. Connect the steering column bulkhead connector to the vehicle wire harness.
  3. Install the two wire harness straps to the steering column wire harness (1).
  4. Install the steering column wire harness (1) to the steering column wire harness retainer (2).
  5. Install the steering column knee bolster.
  6. Install the steering column trim cover.
  7. Verify that the lever is in the center or the OFF position.
  8. Install the steering wheel to the steering column.
  9. Enable the SIR system.
  10. Connect the negative battery cable.
I hope this helps you.

Thanks

Nov 28, 2010 | 2002 Chevrolet Impala

2 Answers

Right turn signals don't work. when park lights are on nothing happens but when park lights are off the right turn signal flashes all the park lights


I had the same problem. It's the blinker switch in the steering column.
You'll need to pull the steering wheel, any cheapo s/w puller will do.
Unscrew the turn signal lever from the steering column. Replace part.
Worked like a champ for me.

Feb 12, 2010 | 1985 Ford F150

3 Answers

I have a 87 blazer s10... the turnswitch /wiper/highbeam switch is broken and is shorting out my brakelights ..i cant seem to get to it.. took the steering weel off but ..?


Unfortunately there are some special tools required you will need to get to the turn-signal switch. Below is the procedure for replacing the turn-signal switch. Generally you can rent the puller from a local auto parts jobber or you can purchase one.
Good luck, let me know how it goes.
Regards,

Many vehicles use a turn signal switch that is separate from the multifunction switch. The steering wheel will have to be removed to gain access to the turn signal switch on these vehicles. The following procedure is a common method of turn signal switch replacement:
  • Place the fender covers on the fenders.
  • Disconnect the negative battery cable.
  • Remove the steering column trim.
  • Remove the horn pad from the steering wheel.
f_aee_cc14.28.jpg Steering wheel attachment. Courtesy of General Motors Corporation, Service Technology Group.
  • Remove the steering wheel and horn collar.
  • Use a suitable puller to remove the steering wheel.
  • With a suitable compressor, compress the preload spring to the lock plate. Compress the spring only enough to remove the snap ring.
f_aee_cc14.29.jpg To remove the snap ring, use the compressing tool to relieve the pressure against the snap ring. Courtesy of General Motors Corporation, Service Technology Group.
  • Use a pick and a small flat blade screwdriver to remove the snap ring.
  • Remove the lock plate, horn contact carrier, and spring.
  • Remove the bolts at the upper steering column support and the upper mounting bracket from the column.
  • Disconnect the turn signal wiring connector.
  • Wrap tape around the wire and connector.
  • Remove the hazard warning knob from the column.
  • Remove the switch retaining screws and remove the switch.
f_aee_cc14.30.jpg Remove the turn signal switch from the column. Courtesy of Chrysler Corporation.
  • Replace the switch and reverse these procedures for reinstallation.

Sep 19, 2009 | 1987 Chevrolet Blazer

2 Answers

Turn signal switch is dead. Not working at all. Not sure where its located to replace the switch


hi how are you? the turn signal switch is behind your steering wheel in the column.must remove horn assembly.then steering wheel,use puller to remove wheel.next remove clip that holds steel plate.(tool required).remove plate.then remove any steering column covers/plastic.then remove screws for turn signal switch.unplug wires and remove.then reinstall in reverse.

Feb 02, 2009 | 1993 Mercury Cougar

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Joe Taylor
Joe Taylor

Level 3 Expert

2228 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...