Question about 1984 Oldsmobile Delta 88

1 Answer

Wheel spindel wheel spindle

Posted by b_ford005 on


1 Answer


  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 179 Answers


Posted on Apr 15, 2010


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

How do you remove a siezed bearing from an 06 corrolla spindle

If you have already removed the spindle then you need to look at the inner side of the spindle (that faces teh car) and look for a snap ring (there should be one on one side of the spindle where the bearing is pressed in, if not then the bearing is pressed in and needs to be removed using a bearing press. this can be done by taking it to a local shop and paying them the nominal fee of like $20- $50(depending on their labor rate) and they will also replace the new bearing in it for you, other wise you are going to have to purchase a bearing press for your self.

May 09, 2011 | 2006 Toyota Corolla

2 Answers

I just did the wheel bearings on my 1985 ford f 150 2 wd i need to find out what the torque is for the nut that holds my wheel bearings and brake rotor on thank you very much

  • There is not a torque speck for that.

  1. Just thread the adjuster into the spindle and tighten real good with a ratchet.
  2. Then rotate the wheel forward to seat them bearings real good.
  3. Give it another tighten then back that adjuster nut off 1/8 of a turn.
  4. Then put the nut lock washer on over the adjuster nut and put a cotter pin in the hole.

  • Your lug nuts are torqued at 100ft lbs though.

Regards, Tony

Apr 28, 2011 | Ford F-150 Cars & Trucks

1 Answer

How do i repair a spindel and hub

I assume you mean a front wheel bearing went out?
Remove the axle nut.
Remove the wheel and brake caliper.
Remove the tierod end by first unbolting, then popping it off with a "picklefork" and hammer.
Remove the bottom balljoint.
Either unbolt the whole strut, or remove the spindle from the rest of the strut.
Pull the spindle off the axle splines.
Take the spindle to a press to push out the hollow stub axle.
Remove the bearing retainer.
The press out the bearing.
Do not use a hammer instead of a press, because it will damage the bearing. But you can use the weight of the vehicle like a press if you are really desperate.

Oct 31, 2009 | 1995 Volkswagen Jetta

1 Answer

I have a 1997 Dodge Ram 1500 4 wheel drive. I

i have found that you need to first make sure the cv shaft is moving free in the bearing. soak everything with penitrating oil. you should be able to move shaft in & out a little. the hub is a very tight fit. you need to tap it some from side to side untill you see a little gap between hub and spindel. then place the head of a flat screw driver in that gap and all around the hub, prying back and forth where ever possible. soak, tap and pry all over. be hard on it if replacing, more gentle if not. good luck.

Jul 17, 2009 | Dodge Ram Pickup 1500 Cars & Trucks

1 Answer

2002 1500 4 x 4 Replacing front wheel bearing hub; can't get to the 3 bolts

to start with, that is not a u-joint cover, it is a cv joint. if this is a chevy. you will have to pull the cv shaft out of the spindel. first loosen the outter tierod nut on the spindel, do not take off completely but just so its on finger tight. get a large hammer and hit the spindel right where the tierod goes through it. a couple of good shots and it should drop out take off nut and move outter tierod aside. now you are gonna do the same thing to the lower ball joint. only when your ready to hit that part of the spindel where the ball joint goes through get a prybar under the upper controll arm and get a budy to push up on it. as long as the shock is still bolted on your in no danger. pull the spindel out towards you from the bottom and you will have enough room to pull the shaft out of spindel to get the nuts. you might have to put ball joint back in without shaft in place to hold spindel still to break those bolts loose. make sure you use new cotter pins on ball joint and tierod nuts

May 30, 2009 | 2004 Dodge Ram 1500

1 Answer

1990 front wheel spindel


Jan 04, 2009 | 1994 Ford Escort

1 Answer

Wheel studs

normally you can take off the spindel but if you remove brake disk and back plate you should be able to punch out the studs with no problem and than push new one in and press it in by tapping it with hammer on the back and than putting some washers over it and than tightening the lug nuts.
Or if you are comfortable with it remove the whole spindel section and put it on a work bench

Jul 21, 2008 | 1995 Ford Escort

2 Answers

Install wheel bearings for 1998 dodge ram 1500

you cant just change the bearings they are sold as one unit spindel and all about $300 bucks for the part.

Jun 21, 2008 | 1998 Dodge Ram 1500 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides