Question about 1997 Subaru Legacy

3 Answers

Timing belt broke and need timing marks diagram 2.2 subaru

Posted by hheather1041 on

Ad

3 Answers

patrick lowbridge

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 289 Answers

The timing marks are on the camshaft pulleys and there are 2 notches on each pulley> they line up with 2 marks on the engine block for each pulley> and the crankshaft has a notch that lines up with a mark on the engine block aswell> pluss the new timing belt will have white marks on it that will line up with all of the marks on the pulleys when they are in the right place so its nearly impossable to do it wrong

Posted on Apr 16, 2010

Ad

Paul Jones

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

1997 subaru outback All Data Timing Marks for a 1997 Subaru outback can be found here !!!!!

http://www.autozmagz.com/subaru/1997-subaru-legacy-gt-sedan-timing-belt-service-and-repair-installation/

Posted on Nov 18, 2010

Ad

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 209 Answers

The timing marks should be on the harmonic balancer

Posted on Apr 07, 2010

5 Related Answers

Bill Hackett

  • 383 Answers

SOURCE: need timing belt mark diagram for 95 corolla 4afe

malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.

Posted on May 06, 2009

robert kious

  • 58 Answers

SOURCE: geo metro timing diagram

woot i feel your pain i had the same problem. go to autozone.com and go to thier vehicle repair.
enter your year make and model and find it. but please hear me on this one.. be carfule thier are like 2 timing references and one timing mark. USE THE DOT. pls i learned the hard way. lol use the dot on the cam sproket. good luck

Posted on Jan 29, 2009

Anonymous

  • 4 Answers

SOURCE: i broke timing belt when replacing hormonic balancer

Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Posted on Jul 01, 2009

c17hydro

Greg Bernett

  • 2989 Answers

SOURCE: 1999 kia sportage timing marks

dfd3ea1.gif Crankshaft match marks


Align marks on timing belt pulley and pump body.

Camshaft pulley alignment marks
9f1c7ef.gif

  1. Align marks on camshaft pulleys with alignment marks on seal plate.
  2. Install timing belt. NOTE: No looseness should exist on the tension side and at the camshaft pulleys.
  3. Loosen tensioner lock bolt.
  4. Turn crankshaft 2 revolutions in direction of rotation and check that timing marks are still in alignment.
  5. Tighten timing belt tension lock bolt to 27-38 ft lb (32-52 Nm).
  6. Apply a force of 22 lbs to timing belt between camshaft sprockets.
  7. Belt deflection should measure 0.30-0.33 in (7.5-8.5 mm)
  8. NOTE: Replace tensioner spring if timing belt deflection is excessive.
Timing Belt Installation


eb770f2.gif
  1. Install lower timing belt cover.
  2. Install upper timing belt cover.
  3. Install power steering drive belt and adjust belt tension.
  4. Install fan pulley.
  5. Install generator drive belt and adjust belt tension.
  6. Install A/C drive belt and adjust belt tension.
  7. Install splash guard.
  8. Install fan and fan shroud.
  9. Install 4 fan bolts. Tighten to 24 ft lb (33 Nm).
  10. Install fan shroud mounting bolts.
  11. Install fresh air duct.
  12. Connect hose to resonance chamber.
  13. Connect battery negative cable.

Posted on Jul 26, 2009

iambanshee74

Kori Policy

  • 3489 Answers

SOURCE: timing belt marks for subaru 1600 ea82 motor with

I would have to send this to you via email due to this sites lack of space. If this is ok, try [email protected] and I will get those right to you free of charge.

Posted on Jun 05, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need timing marks to set timing on 94 Subaru Legacy 2.2 liter


If I was you, I'd pick up a repair manual from your local parts store. It will give you the PROPER procedure, with easy to see and follow illustrations.

Sep 09, 2015 | Subaru Cars & Trucks

1 Answer

HYUNDAI H100 2.6 DIESEL TIMING DIAGRAM


I have a Toyota Town Ace diesel van, the timing belt broke and I need step by step help how to install new timing belt - timing marks diagram.

Jun 24, 2012 | Cars & Trucks

1 Answer

Timing is off


If your timing belt broke chances are you have bent valves and damaged pistons. The vehicle may never start unless you repair the engine damage.

May 21, 2010 | 1997 Subaru Legacy

1 Answer

1993 subaru sportswagan au82motor need timing marks


CLICK on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com

The Timing Belt Marks for the Impreza Wagon and the Legacy Wagon will be the equal of the sportswagon au82motor you have.
http://www.2carpros.com/car_repair_information/year/1993/make/subaru/model/impreza/1993_subaru_impreza_timing_belt_diagram_marks.htm

http://www.2carpros.com/car_repair_information/year/1993/make/subaru/model/legacy/1993_subaru_legacy_timing_belt_diagram_marks.htm

Mar 08, 2010 | 1993 Subaru Legacy

1 Answer

I had a broken timing belt in my 93 legacy I've taken the old belt off and would like to install the new one but i need the belt routing diagram and also need to know were the timing marks go on the belt


CLICK on the following LINK. It has the Timing Belt Diagram you will need.
If you would: Before Clicking let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1993/make/subaru/model/legacy/1993_subaru_legacy_timing_belt_diagram_marks.htm

Mar 03, 2010 | 1993 Subaru Legacy

1 Answer

Impreza 20 turbo 1998 uk timeing marks


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1998 Subaru Impreza. Plus additional Instructional and Directional Diagrams.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1998/make/subaru/model/impreza/1998_subaru_impreza_timing_belt_diagram_marks.htm

Feb 18, 2010 | 1998 Subaru Impreza

1 Answer

1992 Subaru legacy 2.2L SOHC New timing belt can't turn on


Click on the following free direct Link. It has the Timing: Belt and Mark Diagrams for your 1992 Subaru Legacy.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1992/make/subaru/model/legacy/1992_subaru_legacy_timing_belt_diagram_marks.htm

Sep 19, 2009 | 1992 Subaru Legacy

3 Answers

Cant seem to time my 1990 subaru legacy


your timeing marks are on the block rite abouve the cams on either side and on the block in the middle but line the center mark on the teeth there is a mark not the arrow the arrow is where tdc is the mark is on teeth good luck.

Mar 26, 2009 | 1990 Subaru Legacy

Not finding what you are looking for?
1997 Subaru Legacy Logo

4,909 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...