How do you adjust the Aveo parking brake

You parking brake switch is out of adjustment.

Chevrolet Aveo Would not Shift out of Park - Sensor Glitch

sensorglitch.livejournal.com/91859.html

Nov 17, 2009 - Tags, ', aveo, brake light, chevrolet, chevy, gear, park, parking, shift, ]... believe it or not all I had to do was replace the brake switch (a cheap $5 part). ... Theautomatic transaxle shift lever may not shift out of the park position ...
Service Manual2007 Aveo PARKING BRAKEwww.autocats.ws/manual/chevrolet/tis0911/.../Aveo/.../9T2_4G0.EN.htm...Remove the complete parking brake lever assembly and the cable from the assemblyby unfastening the parking brake lever-to-vehicle underbody bolts and ...Missing: 2008How to disconnect the parking brake cable on a Chevy ...? 2:05https://www.youtube.com/watch?v=FxAQMbcHAnQApr 22, 2013 - Uploaded by Josh BruniVehicle Tips: How to disconnect the parking brake cable on aChevy .... How to replace rear brakes and rotors on a 2008 Buick Lucerne ...

Click here to see how to adjust your parking brake.

do not attempt any adjustments. replace the front brakes when they need it. if you try to adjust the proportioning valve you will lock up your back brakes and risk loosing control of your vehicle. you risk ruining the ABS system in your car which will cost you far far more to replace than a cheap set of brake pads. the front brakes do most of the stoping, that is why they wear out much faster than the back brakes. it is VERY IMPORTANT that you DO NOT attempt to adjust your brake proportioning valve.

Check the break lamp sensor. I know it sounds weird, but I had the same problem and that fixed it! I think it's like a $15 part from the dealership.

sounds like brake switch for shifter lock isnt working. UNDER BRAKE PEDAL there should be a cable that leads to the shifter in the mess of wires. make sure its fully connected. If not then unplug and reconnect that should fix if not then issue is at shifter end

the spring in the assembly may be hong up, disassemble and repair if posible

I think, now, i'm not positive, there is a cable adjustment at the bottom of your parking brake handle.

Hello Joe...The Aveo has had it shares of problems, and this is one of them....NHTSA issued several bulletins on the 04 Aveo...this following is the one pertaining to the shift interlock.....

Make : CHEVROLET Model : AVEO Year : 2004
Manufacturer : GENERAL MOTORS CORP.
Service Bulletin Num : 070730007 Date of Bulletin: APR 01, 2007
NHTSA Item Number: 10022265
Component: POWER TRAIN:AUTOMATIC TRANSMISSION
Summary:
AUTOMATIC TRANSAXLE/TRANSMISSION SHIFT LEVER MAY NOT SHIFT OUT OF PARK (REPLACE BRAKE TRANSAXLE SHIFT INTERLOCK (BTSI) SOLENOID). *KB

Take that bulletin number to your dealer and see if they can help.

Untill you can get it repaired heres a little tip for getting it out of park....There is a a little hole in front of their gearshift lever that can correct the problem, temporarily. It should say "brake interlock release" or something like that. With car running, put a key-size object into it and push down while moving the lever. It does not damage the transmission, it just releases the lock. (make sure your foot is on the brake)

Now for the brake light issue...do you have power at the switch you replaced? If so go to the relay and check there...if no power there it's probably a bad ground.

Also...you may or may not know, but the timing belts on these Aveos are prone to failure at aprox 50k ...these failures have caused severe engine damage.
Good luck...i hope the information i've provided you find useful.
Please time to rate me.

Park Brake Adjustment (Disc Brake)

Tools Required

j 21177-A Drum-to-Brake Shoe Clearance Gage

Park Brake Shoe Adjustment

Caution: Refer to Brake Dust Caution.

Important: The park brake shoes must be adjusted before the park brake cable tension is adjusted.Set the J 21177-A so it contacts the inside diameter of the rotor

1. Position the J 21177-A over the shoe and the lining at the widest point.
2. Turn the adjuster nut until the lining just contacts the J 21177-A. Park brake shoe to brake rotor clearance: 0.6604 mm (0.026 in)
3. Repeat steps 1-3 for the opposite side.

Park Brake Cable Tension Adjustment

Important: Before you adjust the park brake cable tension, verify that the park brake shoes are adjusted to provide a clearance of 0.6604 mm (0.026 in) and the rear disc brake rotors are installed.

1. Verify the self adjuster lock-out pin has been removed.
2. Fully apply and release the park brake pedal 3 times.