How do I assemble the front break disc pads on a 2004 Toyota Tacoma 2wd?

Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

? If the brake light is on, check your break fluid level first & top it off. If not, check your break lights - one could be out. Last - it's likely your pads are worn down & need new breaks. Have it checked.

bad neutral safety switch roger.Here's the part. Duralast Neutral Safety Switch JA4058 2004 Toyota Tacoma 2WD 4...

Camshaft Position Sensor

1996 Toyota Truck Tacoma 2WD 2.4L EFI DOHC 4cyl

The Camshaft Position Sensor is located: Under hood, passenger side, front engine area, below valve cover, mounted in distributor

Undo the nuts under hood remove brake caliper remove lower ball joint and tie rod end,remove brake pipe.

Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly









4.0L and 4.7L front disc brake assembly




To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
     and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.

1. Remove a small amount of brake fluid from the master cylinder.
   
2. Install a used brake pad into the caliper and compress the caliper pistons.
   
3. Apply disc brake grease to both sides of the inner anti-squeal shims.
   
4. Install or connect the following:
   
   
   
   • Anti-squeal shims to the new brake pads
     NOTE: When replacing worn pads, the anti-squeal shims must be replaced
     together with the pads.
     
     
   • 2 brake pads
     
   • Anti-rattle spring and the 2 caliper pins
     
   • Clip
     
   • Front wheel
   
   
5. Depress the brake pedal several times to seat the brake pads.
   
6. Check the brake fluid level and top off as needed.

Rear
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Rear wheel
     
     
     
     
     
     
     
     
     
     
     
   • 2 cylinder slide pins from rear caliper assembly
     
   • Caliper assembly from rear caliper mounting
     
   • 2 brake pads with anti-squeal shims from rear caliper mounting
     
   • 2 anti-squeal shims from each disc brake pads
     
   • Pad wear indicator plate from the inner side disc brake pad
     
   • 4 pad support plates from the rear caliper mounting

To Install:

1. Install or connect the following:
   
   
   
   • 4 pad support plates on the rear caliper mounting
     
   • Pad wear indicator plate on the inside brake pad
     Note: Install the pad wear indicator facing downward.
     
     
   • Anti-squeal shims on each brake pad
     
   • 2 disc brake pads with anti-squeal shims to the caliper assembly
   
   
2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
   pins.
   
3. Install or connect the following:
   
   
   
   • Disc brake caliper assembly with 2 caliper slide pins
     
   • Torque to 65 ft-lbs (88 Nm)
     
   • Rear wheel
   
   
4. Depress the brake pedal several times to seat the brake pads.
   
5. Check the brake fluid level and top off as needed.

--- Removal & Installation
Front
To Remove:

1. Before servicing the vehicle, refer to the precautions in the beginning of
   this section.
   
2. Remove or disconnect the following:
   
   
   
   • Front wheel
     
   • Front brake caliper assembly
   
   
3. Make matchmarks on the disc and the axle hub.
   
4. Remove the front disc.

To Install:

1. Align matchmarks and disc onto axle hub.
   
2. Install or connect the following:
   
   
   
   • Front brake caliper assembly with the 2 bolts
     
     
     
     1. Torque to 90 ft-lbs (123 Nm)
     
     
   • Front wheel

need more info if rotors are smooth then possibly a problem in the abs system... is the abs light on...... they do have a failure where you would feel a pulsating feeling let me know

on any toyota trucks like yours you do not need to take calipers out, just insert a screwdriver or pry bar agains the pads and calipers. but do it only one side at a time

check label under hood should be there if not what size engine

Raise the vehicle up and remove the rims & tires

Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.

Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)

Tap the brake rotors off of the hubs, hit them from the back side of the rotor.

No big mysteries here, this is a very easy job.