I have a 2000 Chrysler Sebring. The check engine light is on. The reading is misfire on cylinder 1. Is there a diagram that shows the cylinder by #?

Recheck all work you have done. Sometimes folks replace the wrong coil pack as they can be easily confusing. If everything seems ok, there are still two possibilities. First, ensure that the fuel injector is consistently firing for the cylinder, and also ensure that it is not constantly firing. Either can cause a misfire, one for too little fuel, one for too much fuel. Lastly, check compression in the suspect cylinder. A broken or burnt valve can cause loss of compression, leading to misfires.

were you sure to set the gap on the plugs? and replace them with the correct plug for that matter? also...why was the thermostat replaced?

IF you have a seperate coil (1 coil only) check for correct voltage for the coil as most start on 12 volts and run on 7 volts and have a resistor in the circuit. Randomj misfire may be the coil breaking down as it gets too hot from the incorrect voltage

Diagnose a cylinder misfire condition

Here is a link to give you all Chrysler Firing Orders, it also shows you ththe cylinder #'s : http://www.aa1car.com/library/chrysler_firing_orders.htm

For engine misfiring problem check the help links mentioned below. Click the link below to go through the troubleshooting procedure :---- Engine misses and truck jumps? Hard to down shift? Issue with high gear only? http://technoanswers.blogspot.in/2012/02/engine-miss-and-truck-jumps-hard-to.html

-----------
Bad miss at idle?

http://technoanswers.blogspot.com/2012/01/bad-miss-at-idle.html

-----------
While stop engine idles like cylinder missing?

http://schematicsdiagram.blogspot.com/2012/01/while-stop-engine-idles-like-cylinder.html

------------
Engine Misfire codes for car?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html
Engine Misfire codes?

http://schematicsdiagram.blogspot.com/2011/12/engine-misfire-codes-on-chevrolet.html

--------------
Misfire on cylinder 4?

http://schematicsdiagram.blogspot.com/2011/12/misfire-on-cylinder-4.html

-----------
Oil on spark plugs and car misfires?

http://technoanswers.blogspot.in/2012/02/oil-on-spark-plugs-and-car-misfires.html

----------

This will help.

Thanks.

Most front wheel drive V6 chrysler engines are as follows: standing on passenger side of car facing engine, cylinders 1-3-5 are on the left bank, cylinders 2-4-6 on the right. Standing at the hood facing engine (front of car) #2 is on your left front corner of engine. Change / check plugs and wires before doing and deep sensor testing.

P0302-cylinder #2 misfire detected
P0420- catalyst efficiency below threshold bank 1
P0340-No cam signal at PCM.
The Cam sensor most likely needs to be replaced first. Clear the codes after that and drive and see what comes back on.

Code P0301 = Cylinder 1 Misfire Detected
Start with the “easy to check” items first...Some of these checks/repairs require specialized tools or equipment. A trusted repair shop or dealer would be would be advised to correct this problem.
Try changing the spark plugs, Check the coil, TPS sensor & MAP sensor voltage. Check the fuel pressure, check for vacuum leaks including intake manifold. Dirty or plugged injector, timing, compression test-including leak test--meaning, put #1 on TDC then charge the cylinder with air (~30lbs), and check for leak via exhaust/intake. Update PCM to the latest software, Worn camshaft.

yes disbuter buddie is bad nad its form oil getting in plugs form bad gaskets on valve covers ok so u need new disbuter then gaskets redone stop oil geting in ther i have one these i know it all on this car