Just cheched all fuses none were bad , still cant rear passenger side window to go up . All other windows operate just fine , door locks and power mirrors . please help ... thanks vince ( 2004 jeep grand cherokee laredo )

You say the driver window works? wouldn't be a main fuse or fusible link then -driver door locks and window wouldn't work either. Each door has a module inside (computer) . The driver door has a circuit breaker power feed an a fuse DDM fuse 10amp located in rear junction block circuit breaker is located in under hood maxi fuse block. The circuit breaker also feeds battery voltage to the other door modules too. PDM - passenger door module fuse 10amp located in the instrument panel fuse box and the RDM - rear door module RDM fuse 10amp located in the rear fuse box - under the back seat.

Each power window is connected to a permanent magnet motor. The motor raises or lowers the glass when the door module applies voltage to the motor. The direction the motor turns depends on the polarity of the supply voltage provided by the associated door module. The 2 front doors have their own separate modules. The rear seat contains a single module, which controls both of the rear power windows.
A serial digital communications link, called the simple bus interface, is used for communications between door modules and the driver's door power window switches. The use of serial digital communications allows the use of a single wire to convey switching information between the power door lock switch and the driver's door module (DDM). The serial communication is also used in order to transmit switching information from the DDM to the other 2 door modules.
The door modules apply battery voltage of the correct polarity to the respective window motor when any local, or power door lock switch, UP switch is operated, driving the window up. Battery voltage is applied to the respective window motor in the opposite polarity when any local, or power window switch, DOWN switch is operated, driving the window down.

Driver Door Module (DDM)
The driver's door module (DDM) directly controls the driver's door window motor and the express down window feature. The DDM sends window UP/DOWN messages received from the power door lock switch to the passenger door module (PDM) and to the rear door module (RDM) over the simple bus interface (SBI) line. The DDM also contains a class 2 data link which communicates with the other vehicle system modules. The left front power door locks and the outside power mirror are also controlled through the DDM.
Passenger Door Module (PDM)
The passenger door module (PDM) controls the passenger's door window motor. The PDM controls the passenger's door window directly from the right front power window switch or from instructions over the simple bus interface (SBI). The right front power door locks and the outside power mirror are also controlled through this module.
Rear Door Module (RDM)
The rear door module (RDM) controls both of the rear door window motors. The RDM controls the rear windows directly from the rear door window switches or from instructions over the simple bus interface (SBI).

The following components are used to control the power windows:
• Driver door module (DDM)
• Passenger front door module (PDM)
• LH rear door module (LRDM)
• RH rear door module (RRDM)
• Driver door switch assembly (DDSA)
• RH front power window switch
• LH rear power window switch
• RH rear power window switch
• LH front power window motor
• RH front power window motor
• LH rear power window motor
• RH rear power window motor
• Class 2 serial data link
• DR MOD PWR C/B 30 Amp circuit breaker
• DRIVER DR MOD 10 Amp fuse -- DDSA and DDM logic, DDM internal driver operation.
• PSGR DR MOD 10 Amp fuse -- PDM logic and internal driver operation.
• REAR DR MOD 15 Amp fuse -- LRDM and RRDM logic and internal driver operation

Check all your wires ,make none have rubbed and exposed the bare wire .vibrations might cause the wire to short out on metal

All the wiring for all the windows flow through the master switch...both power and ground. So the problem is most likely a bad master switch or a broken wire in the hinge area of the driver's door. Get a wiring diagram and check for power and ground coming to the switch. If so, then the switch is most likely bad. Read this post http://ricksfreeautorepairadvice.com/window-goes-up-but-not-down/

Try a passenger side door switch or a new complete master switch on drivers door. Alaways check fuses also.

Do you know anything about automotive electronic's ? Serial data Communication network ? Electronic module's inside the vehicle doors , communicate commands ! No relay ,no fuse .
If the passenger mirror is selected and a direction switch is activated, the DDM sends a serial data message to the PDS indicating that the passenger mirror was selected and the direction to be commanded. The PDS will then supply battery voltage and ground to the appropriate control circuits for the direction selected.
DDM - driver's door module

Door Lock System Components
The power door lock system consists of the following components:
• Driver door module (DDM)
• Passenger door module (PDM)
• Door lock relay--Located in the instrument panel (I/P) fuse block and controls the locking of the rear doors.
• Door unlock relay--Located in the I/P fuse block and controls the unlocking of the rear doors
• Body control module (BCM)
• IP BEC
• Reversible door lock actuators in each door

Power Window System Components
The power window system consists of the following components:
• Driver door module (DDM)
• Body control module (BCM)
• Passenger door module (PDM)
• Rear door power window switches
• Power window motors in each of the doors (circuit breaker protected)

Your best bet , take it to a qualified repair shop that has a diagnostic scanner that can pull code's an view input data form these systems . There is one circuit breaker for the window's an fuse's for the lock's . I would think a data network problem . But that would be a guess , without testing anything is possible on these .

First, check all fuses to make sure that none are blown.

If the door lock switch works on the passenger side, then the drivers side door lock switch is probably faulty. Use a multi-meter to test the Drivers Side Door Lock Switch (Black and Pink/Light Green wires unlock the vehicle, and the Black and Pink/Yellow wires lock the vehicle)
If the switch is tested and found to be operating properly, you may have a faulty Body Security Module or Drivers Side Door Lock Actuator.

If neither of your Power Mirrors are working, you probably have a faulty Exterior Rear View Mirror Switch, Power Mirror Module, or blown Central Junction Box Fuse.

If none of your Power Windows are working, you probably have a faulty Accessory Delay Relay or a blown fuse in your Central Junction Box or a faulty Master Window Adjust Switch (all of the Power Window Switches feed through this Master Window Switch). If the Power Windows didn't stop working at the same time, you may have faulty Window Adjust Switches, or faulty Power Window Motors, this is very unlikely though. It would also be a good idea to inspect the wiring for any obvious damage.

I’m happy to help further over the phone at https://www.6ya.com/expert/jeremy_69f3cc28d95bf514

if you can here relays when unlocking/locking check for power at door lock actuators inside doors, if you have power on lock/unlock and good earth from connector actuators are faulty.
if no power on test light when operating check output from central door lock module while operating, none coming out of module then it might need replacing.
check 30Amp power fuse for main relay under bonnet (which goes to pin 8 white/blue on module)and 10Amp gauge fuse in cab(pin 1 blue/red on module),pin 15 is also power when relay is on(red/blue) with test light, and module/ actuators.
check outputs from module pin 3 & 4
blue/red
blue/black
that go to door locks

This may be just a case of inadvertently hitting the window lock out n th driver door window switch by mistake. Check that first. Here's some background on window operation

Principles of Operation
The driver power window regulator motor is controlled directly by the master window/door lock/unlock switch (and its integrated "auto down" module). Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The driver power window regulator motor is a reversible motor that is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The passenger power window regulator motor is controlled directly by the passenger power window switch and can also be controlled by the master window/door lock/unlock switch. Power is supplied to the power window relay and the master window/door lock/unlock switch, and the passenger power window switch when the SEC/timer module grounds the coil side of the power window relay. The SEC/timer module will ground this relay when the ignition is in the ON position and will remain energized for approximately 15 minutes or until the driver or passenger door is opened.
The passenger power window regulator motor is a reversible motor, which is operated by applying power and ground to the motor leads to lower the window, and then reversing polarity on those leads to raise the window.
The power rear quarter glass is also directly controlled by the master window/door lock/unlock switch. The power rear quarter glass power latches also utilize reversible motors. The power rear quarter glass power latches are operated by applying power and ground to the motor leads to open the window, and then reversing polarity on those same leads to close the window.
Symptom Chart Condition Possible Sources Action

• All windows are inoperative

• BJB Fuse:
  • F20.
• Circuit.
• Power window relay.
• Front door power window switch.

• GO to Pinpoint Test A .

• Single power window is inoperative

• Front door power window switch.
• Front door power window regulator.
• Circuit.
• Driver door power window switch.

• GO to Pinpoint Test B .

• Vent power window is inoperative — quarter window glass power latch

• Circuit.
• Quarter window glass switch.
• Quarter window glass power latch.

• GO to Pinpoint Test C .

• The one touch down feature is inoperative

• Master window regulator and door lock switch.

• INSTALL a new master window/door lock/unlock switch. REFER to Switch—Master Window Door Lock/Unlock .

• The back window will not defrost

• CJB Fuses:
  • F30 (10A).
  • F32 (20A).
  • F34 (20A).
• BJB Fuse:
  • F27 (45A)
• Circuit.
• Heated back window switch.
• SEC/timer module.
• Rear window defrost relay.

• GO to Pinpoint Test D .

• The back window defrost will not shut off automatically

• SEC/timer module.
• Circuit.
• Rear window defrost relay.

• GO to Pinpoint Test E .