1994 Lincoln Town Car Signature Series The front passenger electric door lock is locked and I'm unable to unlock it. All the other door locks work just fine when I lock or unlock them. The manual sliding door lock mechanism on the passenger door won't budge. How can I unlock the door without using a blow torch? What's causing the problem and how difficult is it to fix myself? Thanks! Doc

it's part of the door latch assembly , you have to take the door panel on the inside off .
Section 17-02: Lighting, Interior 1997 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/16/2000 Switch, Courtesy Lamp
Removal

1. Remove front door trim panel (23942) and watershield. Refer to Section 01-05 .

1. Remove screw retaining lamp switch (13713) to front door latch (21812).

1. Disconnect lamp switch from body main wiring (14A005).

Installation

1. Follow removal procedure in reverse order.
   
   Interior Lamp Switch
   
   
   
   
   
   Item Part Number Description 1 14A005 Body Main Wiring 2 N610939-S36M Screw 3 14018 Door Ajar Switch 4 21812 Front Door Latch A - Tighten to 1.4-1.9 Nm (13-16 Lb-In)

Door Lock Cylinder LED
Refer to Section 01-14 .

Great news, you can program a 1994 Lincoln Town Car keyless entry remote yourself! Here are the steps:

NOTICE: You must have all remotes on hand when performing this procedure. Any remotes not used during this procedure will become inactive.
1. Turn ignition to RUN or ACC.
(Run is forward, just shy of starting car.)
2. Momentarily jump pins in programming connector located behind the glove box.
(The connector will have two pins inside of it, and it will not be plugged into anything. Jumping the pins means to make a connection between the metal inside the plug. You can do this by using any metal, a metal paperclip bent in the shape of a "U" usually works perfect.)
All doors will lock then unlock to confirm programming mode.
3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote. Door locks will cycle to confirm programming.
5. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
You can find more keyless entry remote programming instructions here https://www.keylessentryremotefob.com/Key-Fob-Programming-Instructions-s/1856.htm

Your locks are out of sync. Lock all doors from Drivers side. Then go around to passenger side unlock, lock and relic. Should be able to unlock doors from drivers side as normal. If not, then one of your actuators are bad.

That noise is due to a failed door lock actuator. This is the electrical device located behind the door panel that is responsible for popping the lock when you press the button. Door lock actuator replacement will eliminate the noise and bring it back to normal operation.

its posss ur lock acculator is going bad in side ur door or poss broken rod handle to door lock acculator or bushing u need to take off door panel and look inside to see if the rod is hooked up

what other year than a 1994 will fit on a 1994 lincoln towncar

it could be a wiring problem check the lock switch at the passenger side probe if there is a +12 volt supply on it. check for blown fuse

IF DOOR LOCKS LOCK AND UNLOCK.WHILE HAND OPERATING DOOR LOCK SWITCH.YOUR REMOTE KEYLESS BATTERY WEAK.IF DOOR LOCKS DONT WORK BY USING YOUR HANDS TO WORK THE SWITCH.LOOK FOR A BLOWN FUSE OR CIRCUIT BREAKER.

The problem is the door lock accuator's and there are four of them, one in each door, they cost about $70.00-$125.00 each

Yes there is a fuse, from the eletrical diagram i am seeing power comes from the power distrubtion box and also fuse in the Fuse box,

Check your fuses for any blown ones. Im seeing a 15amp and 20 amp fuse and a 40amp feed from the distrubtion box.