2007 buick allure headlights will not turn on parking lights work,high beams work. no low beams or daytime running lights

Check the grounds that are near the headlights. You may need an auto-electrician on this fault.

https://www.google.com/search?q=2007+rendezvous+drl+and+headlights+not+working

..

Hello. It seems your Chevrolet has either faulty headlamp relay(s) or its headlamps are connected in series; if one don't light, neither will the other one. I can't explain why the 'CHECK ENGINE' light was still on while your truck's engine was off and key was out of ignition switch. Good luck and keep me informed; if you want to.

Headlamps Inoperative - Low Beams

Step

Action

Value(s)

Yes

No

DEFINITION: This diagnostic procedure should only be used if the high beam headlamps are operating properly and the low beams are inoperative.

1

Did you perform the Headlights System Check?
--
Go to Step 2
Go to Headlight System Check

2

1. Turn the headlamp and panel dimmer switch to the ON position.
2. Move the headlamp dimmer switch to the LOW position.
3. Backprobe the headlamp dimmer switch connector with a J 35616-200 from cavity A to ground.

Does the test lamp light?
--
Go to Step 3
Go to Step 5

3

1. Remove the daytime running lamp relay.
2. Connect a J 35616-200 at cavity G5 to ground.

Does the test lamp light?
--
Go to Step 4
Go to Step 6

4

1. Re-install the daytime running lamp relay.
2. Backprobe cavity B at the high/low beam headlamp with the headlamp dimmer switch in the LOW position.

Does the test lamp light?
--
Go to Step 7
Go to Step 8

5

Replace the headlamp dimmer switch.

Is the repair complete?
--
Go to Headlight System Check
--

6

Repair the open in CKT 359 (PPL) between the headlamp dimmer switch and the daytime running lamp relay.

Is the repair complete?
--
Go to Headlight System Check
--

7

Replace the high/low beam headlamps.

Is the repair complete?
--
Go to Headlight System Check
--

8

1. Inspect for an open in CKT 12 (TAN) between the daytime running lamp relay and S120, repair as necessary.
2. Replace the daytime running lamp relay if no open was found in CKT 12 (TAN) between the daytime running lamp relay and S120.

Is the repair complete?
--
Go to Headlight System Check
--

This is usually caused by a failed front control module as this unit controls the lighting on the vehicle!
--------
airbag reset tool

Headlamps
The headlamps are operated when the driver places the headlamp switch in the HEADLAMP position. The LT HDLP and RT HDLP fuse in the IP fuse block, supply battery positive voltage to both the left and right headlamps. The low beam and high beam circuits continue to the headlamp switch. Depending on the position of the dimmer switch, either the low or high beam circuit will now have a path to ground. Ground is provided at G204. The low beam and high beam circuits also provide the body control module (BCM) with both low and high beam inputs. The headlamp switch includes the dimmer and the flash-to-pass switch.
If the headlight switch is left in the HEADLAMP position, the headlights will remain on until turned off or the battery runs dead.
Daytime Running Lamps (DRL)
Any function that turns on the headlights will cancel the daytime running lamps operation. The LT HDLP fuse in the IP fuse block supplies battery positive voltage to the daytime running lamp (DRL) relay coil circuit. The DRL relay switch contacts are connected to the low beam circuit. When the headlamp switch is placed in the OFF position, the BCM will turn on the daytime running lamps. The BCM energizes the DRL relay, closing the switch contacts and grounding the low beam circuit at G204. The DRL illuminate the low beam headlights at a reduced intensity. The DRL will operate when the ignition switch is in the RUN position, the gear selector is not in the PARK position and the parking brake is released. When these conditions have been met the DRL will illuminate.
DRL operation in Manual Transmission equipped vehicles will occur when the ignition switch is in the RUN position, and the parking brake is released.

Probably the dimmer switch . But without testing that would be just a guess . Turnning the headlamps on Any function that turns on the headlights will cancel the daytime running lamps operation..
No ,don't think the DRL relay has anything to do with it .

View wiring diagrams an testing the electrical circuits at the dimmer switch would be the proper way to diagnose .

[Information] For a 2002 Toyota Camry, the Daytime Running Lights (DRL) operate utilizing the High Beams (inner Lamps closer to the center of the vehicle front) at a reduced power.

[The troubleshooting process:] Review the Owner's Manual and ensure the test configuration matches the following criteria:
1. According to the 2002 Toyota Camry Owner's Manual (Check your Owners Manual):
"The DRL system will make your headlights come on at a reduced brightness when:
The light switch s in the "DRL" position.
The ignition is on with the engine running.
The headlight switch is off.
The parking brake is released."

2. Set the Test Conditions according to Step 1 above.

3. Check the headlight bulbs to ensure they are not burned out. If one burns out, there is a fair chance that the other would have burned out at the same time. Replace as necessary. In this case, if the high beams operate, the DRLs should also operate.
4. Test the system, ensuring the step 1 conditions are set. (Engine running, Multi-function Switch on Turn Signals in "DRL" position, headlight switch off (repeating what the manual says -- it should be obvious that in the "DRL" position, the headlight switch should be off / do not have the switch positioned to "High Beam"), and the Parking Brake "off").
5. If DRL lights do not work, check the engine compartment Fuse and Relay Box. there is a 5 Amp DRL fuse -- replace it with the spare. Test (step 4).
6. If it does not work, swap around or replace relays -- there are three (3). Any one of them could be bad (stuck or burned out). Test (step 4).
7. Other less likely possible issues could be that the Multi-function Switch is broken or a connection / wire is broken. [Beyond the scope of this process.]

My problem was that the test configuration did not have the engine running and parking brake off - Step 1. Problem solved with much thought, repetitive tests on the vehicle and going back to the basics -- what does the Owner's Manual say and where are the applicable fuses and relays located?

suspect low beam head light fuse, check fuse if ok suspect that both low beam head lights are burned out ( it happens) ,if ok suspect headlight dimmer switch.

The blinking light is telling you that you have a headlight out, if you look the service light should be coming on when the light stops blinking.
Replace the head light and all should be fine.

Sounds like you need a bulb,the daytime running lights send power to the high beam wire so they look like low beam lights are on but really they are high beam lights running on low voltage.

the click you are talking about is the high beam relay.
you nedd to get a tester or voltmeter and check the sockets for 12v.
there has been instances where both low beam bulbs went at once.
do the daytime running lights work?
if not,supect the daytime module...it is also wired into the parking brake.
if you put the park brake on first,then start the vehicle,the dtr do not come on