Question about 1999 Dodge Ram 2500 4WD

1 Answer

Would like to know if you can put a toggle switch on the pto wire on a 24 valve cummins 1999 if it will bring the idle up?have engine and wiring for engine,have the cummins computer that is on the engine,do not have truck computer.

Posted by Allen Hermsen on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 310 Answers

You can do it, you have tap into the compter
but its easyer to buy a kit with a chip off ebay and instalt it so all you do is unplug and replug stuff

Posted on Feb 11, 2010

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 Isuzu Rodeo, high idle problem.


po161 O2 sensor bank 2 sensor 2 after catalytic.

Jul 05, 2016 | 1999 Isuzu Rodeo

1 Answer

Where can I get a wiring diagram for a 1997 Dodge RAM 3500 diesel pickup?


1997 3500 Wiring Diagram - Dodge Diesel - Diesel Truck Resource Forums

www.dieseltruckresource.com/...dodge-ram.../1997-3500-wiring-diagra...
Jan 24, 2011 - Hey guys, I'm working on a 97 3500 that's had the bed removed and replaced with a flatbed. There is the biggest mess under that truck wiring wise and. ... 2007 Ram 3500 A/C compressor wont engage, need wiring diagram ...

Dodge Wiring Diagrams / Schematics - YouTube

? 1:13
https://www.youtube.com/watch?v=UI6_vhCHFYU
Nov 19, 2013 - Uploaded by Robert Nauert
Dodge Wiring Diagrams / Schematics ... Nitro, Power Wagon, Ram 1500, Ram 2500, Ram 3500, Ram 4500 ...

1997 Dodge Cummins - Full color wiring diagrams - 12 Valve ...

forum.mopar1973man.com/.../1638-1997-dodge-cummins-full-color-wi...

Jan 01, 2016 | Dodge Cars & Trucks

1 Answer

I rebuilt a 98 cummins 24 valve. How do I wire it up to run


Check the Cummins web site, you can probably download this information quite easily. When following the wiring diagram, remember that things like oil sensors, temperature sensors etc are probably more important than actuaklly running the engine first time out. You NEED to monitor oil pressure and temperature closely tio ensure you don't "COOK" all your hard work.

Oct 06, 2012 | Cars & Trucks

1 Answer

I need to know where it's located and how to take off and put on idle control switch


Disconnect the negative cable from the battery terminal...Locate the IAC valve on the side of the engine, near the intake...Remove the electric cable on the back of the IAC valve. Remove the screws that attach to the IAC valve and set them aside...
Pull the IAC out of the Cadillac DeVille and replace with new valve...Connect the IAC valve to the wire and reconnect the screws. Turn the screws so that they are completely tightened...Reconnect the negative cable to the battery and start engine to test valve.

Good luck, i hope this helps.

Jun 30, 2011 | 1999 Cadillac DeVille

1 Answer

Ignition switch wont engage starter. a wire has been hooked up from the starter to a toggle switch. engine starts but then dies after about 5 seconds


if there is a coil on that model bring small wire from positive on battery to positive side of coil and see does it keep running ,if it does check ignition switch and wiring to switch

Mar 03, 2011 | 1999 Chevrolet S-10 Pickup

2 Answers

I have the following fault codes reading


P0216 - injector timing control circuit

P0234 - turbo / supercharger over boost condition

P0523 - engine oil pressure sensor / switch circuit high inout.

Jan 22, 2010 | 1998 Dodge Ram 3500 2WD

1 Answer

I need the required valve clearance for a 98 1/2 dodge 5.9 24 valve cummins diesel engine


there should be a tag on your engine with recomended valve clearances.

Dec 21, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Starting system wiring diagram for a 86 ford e550/100


Have you located your local Cummins Dealer for this. It should be no issue for them to copy/email a diagram. Good luck...

Jul 13, 2009 | 1986 Ford Econoline

1 Answer

Engine shuts off when I put it on Reverse !


Idle may be too low. A lock screw is at the back of the P7100 mechanical engines, or 12 valve engines. If VP44 or 24 valve you need a dealer to change idle in the ecm. good luck...

Apr 03, 2009 | 2006 Dodge Ram 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...