What is connecting rod bolt torque specification 1999 KIA Sportage

2008 kia sportage 2.0 timing belt diagram AND ...

JustAnswer https://www.justanswer.com > Kia Troubleshooting
May 1, 2019 - Install the timing belt lower cover(A) with 5bolts(B). Tightening torque : 7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lbf.ft). 15. Install the ...

1 answer · Top answer: Glad I can help! Please let me know if you have any further questions.

TIMING COVER REMOVAL, TIMING COVER OIL LEAK FIX ...

YouTube · Electrical Car Repair LIVE 6K+ views · 2 years ago
21:35
TIMING COVER REMOVAL, TIMING COVER OIL LEAK FIX KIA SORENTO, KIA SPORTAGE If you have Kia Sorento Sportage and you need to replace timing ...

..

What are the cylinder head torque settings for a KIA K2700

www.answers.com > ... > Categories > Cars & Vehicles > Asian Cars > Kia
What is the torque specification for the cylinder head on a 2002 Kia Sportage? ... the correct torque for cylinder head bolt of kia pregio 2.7 diesel is 130-135ft-lbs. ... Thehead bolt torque settings, on your Kia 2.7 diesel engine, is 70 pounds per ...

head bolt torque and start with right one

The information you need is typically found in a vehicle shop manual or aftermarket repair manual. I'm sure you already knew that, so rather than going out and buying the manual you need go to www.autozone.com and register for free. The free registration will give you access to online repair manuals which will have all the info you need. Keep in mind that the bolts need to be torqued in a specific sequence.

TORQUE SPECIFICATIONS kia rio
Cylinder Head Bolts:
(21.7ft.lb) or (3.0kgf.m) 90?

Hi Zak:
Kia Sportage 1998-02 Repair Guide
Oil Pan - Removal & Installation

1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
2. Drain the engine oil.
3. Remove or disconnect the following:
   
   Negative battery cable 2 Top intake manifold bracket bolts Front 3 axle housing mounting bolts, 4WD only Left front bushing from the axle housing mount and lower the front axle housing Both gusset plates from the engine Transmission under cover Engine under cover Oil pan mounting bolts and using a scrapper tool separate the oil pan Oil pan Oil strainer assembly Oil baffle
   


Fig. Exploded view of the oil pan assembly mounting

To install:



Fig. Tighten the oil pan bolts in sequence

1. Clean the engine block, oil pan and baffle pan surfaces of any gasket material.
2. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the baffle pan.
3. Install or connect the following:
   
   Oil baffle. Torque the bolt to 84 inch lbs. (9.5 Nm). Oil strainer. Torque the bolts to 84 inch lbs. (9.5 Nm).
   
4. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the oil pan.
   
   Oil pan. Torque the bolts to 84 inch lbs. (9.5 Nm). Transmission under cover. Torque the bolts to 84 inch lbs. (9.5 Nm). Gusset plates to the engine. Torque the bolts to 33 ft. lbs. (45 Nm). Engine under cover Front axle housing into position. When properly aligned, torque the bolts to 48 ft. lbs. (65 Nm). Intake manifold bracket bolts. Torque the bolts to 34 ft. lbs. (65 Nm). Negative battery cable
   
5. Fill the engine with clean oil.
6. Start the vehicle and check for leaks, repair if necessary.

Hope helps with this (remember rated this) Good luck.

I need the torque settings and pattern for a Kia Sportage 2.2

The gasket has metal torque limiters.use your own judgement just dont break the bolts

Head bolts- 62 lb-ft cam pulley lock bolt- 42 lb-ft cam cap bolt- 16 lb-ft

hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .

1999 kia sportage 2.0 DOHC head torque

Thanks for using FIX YA !

J5