Question about 1991 Jeep Wrangler

2 Answers

Where is the bleed valve for clutch on a 1991 jeep wrangler

Posted by bridgett_m on

Ad

2 Answers

Anonymous

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 437 Answers

1. Fill master cylinder reservoir with DOT 3 brake fluid. Raise and support vehicle. Attach bleeder hose to bleeder screw on bleed line of slave cylinder. See Fig. 1 (attached in link) . Place other end of hose in glass container 1/2 full of brake fluid. Loosen bleeder screw while holding bleeder screw fitting.

2. Have an assistant depress clutch pedal to the floor. Tighten bleeder screw and release clutch pedal. Repeat bleeding procedure until fluid entering container is free of bubbles. DO NOT allow reservoir to run out of fluid during bleeding. Refill clutch master cylinder reservoir.

CAUTION: DO NOT allow bleed line to bend or flex when loosening
bleeder screw.

FIG1: http://anubiscycle.com/fixya/91wranglerslaveassy.png

Posted on Jan 14, 2010

Ad

Danny Faulk

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 10 Answers

The location is in the same place as a 92 Jeep, it's on the slave
cylinder. follow the break line from master cylinder down to slave cylinder.
the bleader is on that cylinder.

Posted on Nov 03, 2012

Ad

2 Related Answers

Anonymous

  • 2 Answers

SOURCE: how do I bleed hydraulic clutch in 1991 jeep

There is a bleeder on the drivers side of the transmission follow the tube from the clutch master cylinder if you cannot find it. Pump the clutch up and hold it down then open the bleeder repeat till air is gone. May have to bleed again after driving a bit. If you want to bleed the clutch master cylinder run a tube from where the line goes into the cylinder and take the cap off and run the tube into the fluid (make sure its in the fluid) then pump the clutch slowly until no air bubbles. I just replaced my clutch master cylinder this is where the information comes from hope it helps you out!

Posted on Apr 05, 2009

emissionwiz

Marvin

  • 85239 Answers

SOURCE: 1991 jeep wrangler clutch

U have what is called a hydraulic clutch, one of the hydraulic cylinders hs failed, there is a master and a slave cylinder. The most likely and most common cylinder to fail is the slave cylinder, this requires the transmission to be pulled out to replace it. the art is around $125.00, while the trans is out u might as well replace the clutch, the labor is about the same. Here is a picture of the part, let me know if u can see it.



1abd4ec.jpg

Posted on May 13, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

Where do you bleed the clutch at on a 1997 jeep wrangler what is the location of it


This all depends if this is a hydraulic clutch or if its cable operated, you can only bleed hydraulic clutches, to bleed it you would bleed at the ******, you will see the bleeder screw on the slave cylinder that operates the clutch fork.

Sep 03, 2011 | 1991 Jeep Wrangler

1 Answer

No pressure on clutch tryn to bleed and let reservoir run empty,,havnt gpt it back,,,dont know what to do?????please help


put a bar behind clutch arm on gearbox and pull it in so the slave cylinder goes in ,then open bleed valve,now assistant pumps up the clutch so the slave pushes out then put bar in the arm again and pull in back with the bleed valve open then when its in cles it and repeat operation again and it should be`perfect,if not push pedal down and jam it down with a brick and leave overnight that normally works

Aug 25, 2011 | 1991 Jeep Wrangler

1 Answer

Looking for picture of clutch bleed valve


on the drivers side of the bellhousing the bleeder valve it located on top of the clutch slave cylinder

Jan 21, 2010 | 1991 Jeep Wrangler

1 Answer

94 jeep pick up can't get the hydralic clutch bleed


need to free flow, means to open bleed valve open and let it run down but adding fluid to till you dont see air bubbles.
use a clear pice a hose, hook it to bleeding valve and into a bottle with 1/4 full of fluid will take few tries.

Feb 15, 2009 | 1991 Jeep Wrangler

1 Answer

How do i bleed the tranny lines in 1991 jeep manual transmission


Auto parts stores have whats called trans. cooling line flush just ask them and they will know what you want.

Feb 09, 2009 | 1991 Jeep Wrangler

2 Answers

1991 jeep wrangler not shifting into gear could this be clutch


I would first bleed the tranny lines, if that doesnt work then your tranny is out and need to get it replaced. FYI with Jeep Wranglers, It is better to get a new transmission then to rebuild them

Feb 09, 2009 | 1991 Jeep Wrangler

1 Answer

How do you bleed the clutch in a 1991 Jeep Wrangler?


If replacing just the fluid, you should gravity bleed it by opening the valve at the side of the transmission where the line goes in to connect with the slave cylinder. Be sure to stand by and keep the tiny reservoir from going empty during bleeding, or you just make things worse. Assume you replaced parts. Is this right or wrong?

Or are you just trying to restore performance in a poorly operating system? Would help TONS to know these details, and how much you know about bleeding, etc. If you are trying to bleed a new slave cylinder, it can take 600 to 1800 pumps of the clutch pedal sometimes to clear it out manually. If you want instructions on how to bleed in with vacuum assistance, please post request comment to that effect.

Talk to you soon. TT

Feb 06, 2009 | 1991 Jeep Wrangler

Not finding what you are looking for?
1991 Jeep Wrangler Logo

1,767 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...