Question about Nissan Altima

1 Answer

Windshield wipers won't move

Otor runs but windshield wipers won't move

Posted by mattmwork on

Ad

1 Answer

cock cock

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 486 Answers

A LINK HAS COME OF THE MOTOR/ DRIVE , NEED TO ACCESS CONTROL RODS AND RECONNECT

Posted on Dec 26, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WINDSHIELD WIPER CLUTCH/TRANSMISSION ALIGNMENT


one of the arms under the firewall came off look down through where wiper motor is

Feb 26, 2018 | 2002 Saturn Sl

1 Answer

Just replaced the wiper motor on Jetta and wipers still won't work


Have you replaced only the motor or including the gear box (where the input shaft to the linkages is located)?

Oct 23, 2012 | 1999 Volkswagen Jetta

1 Answer

2000 Buick Regal windshield wipers stopped working during hard rain.


Make sure wiper arms are tight they are on a spline also where the wiper arm transmissin conects to the wiper motor therw is a nut that holds a z shaped bracket that losens up and oblongs the rectangular slot so the wipers stop with the least resistance.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/craig_a14a43e01fd0835a

Nov 20, 2017 | 2000 Buick Regal

1 Answer

Hi I've got a c class 2006 and my wipers are only working when I'm actually driving as at above say5 mph. If I'm stationary at traffic lights or a junction then they won't work?...


i replied to this in your follow up question, but will add this also,, replace the wiper blades, and also,, clean your windshield with a windshield cleaner wax, your wipers could be old, and actually sticking or dragging not letting the vacuum drive at low idle move them

Aug 11, 2011 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

The windshield wipers on my Chevy Blazer 97 stopped working,just makes a sound, but not moving? What do I need to check/replace?


Sounds like the windshield wiper motor needs to be replaced. The gear inside may be stripped so you'll hear it running but it won't do anything. I've had that happen with the rear wiper motor. Hope that helps.

Jun 15, 2010 | 1997 Chevrolet Blazer

1 Answer

Need to get a programmer dont know where its at


  • Windshield Wipers Continue to Run When Turn Signal and Windshield Wiper Switch Are Turned OFF
  • Damaged turn signal and windshield wiper switch .
  • Damaged windshield wiper motor .
  • Damaged windshield wiper control module.
7fd52e7.gif
efd7dbe.gif
Pin Number Circuit Circuit Function 1 57 (BK) Wiper Motor Ground (Park) 2 28 (BK/PK) Wiper Module to Wiper Motor (Park Switch) 3 65 (DG) Wiper Motor Power (Park Feed) 4 61 (Y/R) Wiper Motor Common (RUN) 5 56 (DB/O) Wiper Motor LO 6 58 (W) Wiper Motor HI
Windshield Wiper System The windshield wiper system consists of :
  • Windshield wiper motor (17508) (F-type).
  • Washer system.
  • Windshield wiper control module.
  • Turn signal and windshield wiper switch (13K359).
The windshield wiper control module is:
  • Located at the instrument panel fuse panel.
The windshield wiper motor is:
  • Attached to the cowl top extension (021A36) .
  • Connected to windshield wiper mounting arm and pivot shaft (17566) .
The turn signal and windshield wiper switch features a:
  • Rotary wiper switch.
  • Push type washer actuator.
OFF/Low/High Speed
  • Has a two-speed, permanent magnet, three brush electric windshield wiper motor .
  • The windshield wiper motor has a brush rigging that permits selection of low or high speed.
  • When the turn signal and windshield wiper switch is in the LO position, the common brush and the blue/orange wire brush are used, and the windshield wiper motor operates at low speed.
  • When the turn signal and windshield wiper switch is in the HI position, the common brush and the white wire brush are used.
  • In HI position, electric current will bypass a portion of the armature winding causing the windshield wiper motor to operate faster.
  • When the turn signal and windshield wiper switch is moved to the OFF position, the windshield wiper motor will continue at low speed until the park switch outer contacts open.
  • When the park switch contacts open, the windshield wiper motor stops in the park position.
Interval
When the turn signal and windshield wiper switch is in the interval position:
  • The wipers make single wipes separated by pauses.
  • The rotary switch is on the end of turn signal and windshield wiper switch .
  • The length of the pause can be set from approximately 1 to 17 seconds.
  • Length of pause decreases as the rotary switch is rotated away from off.
  • Length of pause increases as the rotary switch is rotated toward off.
While in the interval wiper mode:
  • It is normal to hear a slight click at the beginning of each on/pause cycle. NOTE: When using interval wipers, the first wipe may not occur until after a pause of up to 17 seconds.

May 27, 2009 | 1994 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

321 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14847 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...