Question about 1999 Cadillac DeVille

1 Answer

Rear suspension low to ground - 1999 Cadillac DeVille

Posted by floydtracy85 on

Ad

1 Answer

Marvin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cadillac Master
  • 85,239 Answers

Your rear air suspension bags are leaking, u will need to have them replaced, this job requires a service factory manal and tha proper safety procedures be followed, so it is best left to an expert.

Posted on Dec 25, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My drivers side rear wheel turns in and out. Could this be my control arm?


It is Nomo like that and it is your low and hi suspension travel.Check your wheel bearing is well.

Jan 30, 2017 | Cars & Trucks

2 Answers

My lancer is too low n carrying passengers in it it tends to touch the ground how do i fix it?


Depends on the age of the car, but it sounds like the suspension needs work. You may want to get the springs and shock observers looked at.

Nov 29, 2014 | Cars & Trucks

1 Answer

I have a 2001 town car with a suspension problem. I just replaced the air bags. A month later the pump started to run too much. I tried soapy water but found no leaks.Yesterday the back end droped and the...


Having it hooked up to a factory scan tool would be your best bet . Check for DTC'S diagnostic trouble codes . Without testing ,code scan ,we'd only be guessing .
Very complex , the untrained person hasn't got a pray of fixing this . You have no idea what your dealing with . Vehicle Dynamic Suspension The vehicle dynamic suspension consists of the following components:
  • Rear air suspension control (RAS) module (5A919)
  • Snorkel
  • Drier
  • Air compressor (5319)
  • Air suspension switch (5K761)
  • Solenoid valve (5311)
  • Air spring (5560)
  • Air suspension height sensor (5359)
  • Air line
  • Rear Air Suspension Control Module
    A microprocessor controls the air suspension system. The microprocessor and its supporting hardware are contained in the rear air suspension control module. The rear air suspension control module responds to signals from various sensors in the vehicle to maintain the programmed ride height while the vehicle is either moving or stopped. The rear air suspension control module accomplishes this by opening and closing solenoid valves to control the amount of air in the air spring(s). The rear air suspension control module turns on the compressor by applying voltage through the compressor relay to inflate the air spring(s) and raise the vehicle. The rear air suspension control module opens the vent solenoid to lower the vehicle by releasing air from the air spring(s) in response to signal inputs from the air suspension height sensor(s).
  • Rear Air Suspension Control Module Diagnostic Trouble Code (DTC) Index DTC Description Source Action B1317 Battery Voltage High Rear Air Suspension Control Module GO to Pinpoint Test C . B1318 Battery Voltage Low Rear Air Suspension Control Module GO to Pinpoint Test C . B1342 ECU Is Defective Rear Air Suspension Control Module INSTALL a new rear air suspension control module. REFER to Module-Air Suspension Control . TEST the system for normal operation. C1441 Steering Sensor Channel A Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1442 Steering Sensor Channel B Circuit Failure Rear Air Suspension Control Module REFER to Section 211-00 . C1722 Air Suspension Height Sensor Power Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1723 Air Suspension Height Sensor Power Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test E . C1760 Air Suspension Rear Height Sensor High Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1763 Air Suspension Rear Height Sensor High Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test G . C1765 Air Suspension Rear Height Sensor Low Signal Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test F . C1768 Air Suspension Rear Height Sensor Low Signal Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test H . C1770 Air Suspension Vent Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test I . C1773 Air Suspension Vent Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test J . C1790 Air Suspension LR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test K . C1793 Air Suspension LR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test L . C1795 Air Suspension RR Air Spring Solenoid Output Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test M . C1798 Air Suspension RR Air Spring Solenoid Output Circuit Short to Ground Rear Air Suspension Control Module GO to Pinpoint Test N . C1813 Air Suspension Vent Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test O . C1818 Air Suspension Air Compressor Request Exceeded Max Timing Rear Air Suspension Control Module GO to Pinpoint Test P . C1830 Air Compressor Relay Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test Q . C1832 Air Compressor Relay Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test R . C1840 Air Suspension Switch Circuit Failure Rear Air Suspension Control Module GO to Pinpoint Test S . C1842 Air Suspension Switch Circuit Short to Power Rear Air Suspension Control Module GO to Pinpoint Test D . C1897 Steering VAPS Circuit Loop Failure Rear Air Suspension Control Module REFER to Section 211-00 . U1041 SPC Invalid or Missing Data for Vehicle Speed

Nov 12, 2017 | 2000 Lincoln Town Car

3 Answers

When my envoy sits overnight my rearend drops down


There has been a service bulletin for that type of concern. Here is what it states.









Suspension - Rear Suspension Is Low/Sagging/Uneven

Notes




ENGINEERING INFORMATION

Bulletin No.: 06-03-09-006B

Date: December 15, 2008
Subject:
EI06006 - Rear Suspension Uneven, Sagging, Low (Recalibrate Air Spring Sensor)

Models:
2006-2007 Buick Rainier
2006-2007 Chevrolet TrailBlazer SS
2006-2007 GMC Envoy, Envoy XL
2006-2007 Saab 9-7X


with Suspension Pkg - Rear Load Leveling (RPO G67)

Supercede:

This bulletin is being revised to update the labor operation in the warranty information. Please discard Corporate Bulletin Number 06-03-09-006A (Section 03 - Suspension).

Condition

Some customers may comment on the rear suspension being uneven or sagging.

Correction

DO NOT REPLACE THE COMPRESSOR.

Based on technician feedback, engineering has determined that the customer's concern can be corrected by recalibrating the air spring sensor. Refer to the Trim Height Uneven or Low diagnostics and Air Spring Sensor Calibration procedure found in SI.

Nov 29, 2011 | 2004 GMC Envoy

1 Answer

Rear suppenion low to the ground


There is an air compressor mountedmabove the rear suspension. The fuse for the air ride suspension is located behind the trunk rear trim panel. There is a level sensor on the rear control arm. If fuse is good, check for power at plug feeding compressor, compressor failure common. With suspesion at low position, sensor should send power to compressor. if no power suspect height sensor. Check relay for power and operation although failure rare.

Dec 25, 2009 | 1999 Cadillac DeVille

1 Answer

Rear shocks are causing car to be lifted high off the ground


the leveling switch on the rear suspension could be out of adjustment - it turns the pump on when rear is to low and turns off when level

Sep 28, 2009 | 1998 Cadillac DeVille

2 Answers

The rear suspension


you need rebuilt or new air struts.their easy to change but you should have a lift it makes it very easy.

Aug 17, 2009 | 1993 Lincoln Continental

2 Answers

Can any one tell me were how i can find the automatic level control on my 1994 town car


Description and Operation The rear air suspension:
  • Is an air-operated, microprocessor-controlled, suspension system.
  • Replaces the conventional rear coil spring suspension.
  • Provides low spring rates for improved ride and automatic rear load leveling.
  • Is standard equipment on the Town Car.
  • Is available as optional equipment on Crown Victoria and Grand Marquis.
The rear air suspension system has the following features:
  • The system is operational with the ignition switch in the RUN position.
  • Automatic rear load leveling has limited operation for one hour after ignition switch is turned to OFF.
  • The air suspension switch, located on the right side of the luggage compartment, must be turned OFF when the vehicle is on a hoist, being towed or jump started.
  • The Air Suspension warning indicator is located in the instrument panel, to the right of the speedometer.
    • The warning indicator flashes five times and then stays on when service switch is turned off or a system malfunction is detected.
  • The rear leveling system operates by adding or removing air in the springs to maintain the level of the vehicle at a predetermined rear suspension D ride height dimension, and is controlled by a control module (5A919) .
  • The rear air suspension control module also controls the electronic variable orifice (EVO) steering.
  • Refer to Section 11-02 for Description of the EVO steering system.
  • Air required for leveling the vehicle is distributed from the air compressor to the rear air springs by a nylon air line which runs from the compressor air dryer (5346) through a Y-fitting to each individual air spring.


Suspension, Computer Controlled—Town Car

c441c13.gif
Item Part Number Description 1 9C392 Compressor Relay Power Junction Block 2 5A897 Air Line (Attached to Brake/Fuel Bundle) 3 5319 Air Compressor With Regenerative Air Dryer and Vent Solenoid 4 5A897 Air Line to Compressor 5 5K761 Air Suspension Service Switch 6 14489 Data Link Connector 7 — Quick Connect 8 — To LH Air Spring 9 — From Compressor 10 — Y-Fitting (Part of 5A911) 11 — To RH Air Spring 12 5A908 Heat Shield 13 5A966 Spring Retainer Clip 14 5560 Rear Spring 15 5359 RearAir Suspension Height Sensor 16 5A919 Control Module 17 14018 Air Spring Solenoid

Control Module Power and Ground The control module (5A919) has the following features:
  • Power is provided by Circuit 418 and is controlled by the air suspension switch.
    • The air suspension switch is powered through a 15 amp fuse in Circuit 296 in Town Car.
    • AIR SUSPN PUMP (30A MAXI) fuse provides this power through Circuit 414 in the Crown Victoria/Grand Marquis.
  • Control module ground is provided through control module wire harness Pins 6 and 21, to the RH inner quarter panel sheet metal, near the control module .
---------------------------------
Weight Added When weight is added to the vehicle:
  • The air suspension height sensor (5359) length is reduced from trim length, sending a "rear is low" signal to the control module (5A919).
  • The control module then turns the compressor on by grounding the compressor relay control Circuit 420. This restores the rear of the vehicle to trim position.
    • Battery voltage is provided to the relay coil by Circuit 414.
  • The control module opens the spring solenoid valves (5311) by switching Circuits 416 and 429 to ground. This allows pressurized air to enter the springs.
    • Battery voltage is provided to the air spring solenoid valves by Circuit 414.
  • Compressed air flows from the compressor, through the compressor air dryer (5346) airlines and spring solenoid valves into the rear springs (5560).
  • As the rear springs raise the rear body height, the air suspension height sensor increases in length until the preset trim height is reached.
  • The control module then turns off the compressor (through the relay) and closes the air spring solenoid valves.
----------------------------------------------------------------------
Weight Removed When weight is removed:
  • The air suspension height sensor (5359) length is increased from the trim length, sending a "rear is high" signal to the control module (5A919).
  • The control module then opens the vent solenoid valve (located in the compressor assembly) by switching Circuit 421 to ground and opens the solenoid valves (5311) by switching Circuits 416 and 429 to ground. This restores the rear of the vehicle to trim position.
  • Compressed air flows from rear springs (5560), through the air spring solenoid valves, air lines, compressor air dryer (5346), and out the vent solenoid valve.
  • As the body lowers, the air suspension height sensor length decreases until the preset trim height is reached.
  • The control module then closes the vent and solenoid valves.
-----------------------------------------
Control module operates as follows:
  • In general the control module uses a 45-second averaging interval to determine when compress and vent operations are needed.
  • However, door courtesy lamp switch (13713) inputs can override the 45-second averaging interval so compress and vent operations can begin immediately, if needed.
  • The 45-second averaging interval is used to keep the control module from making unneeded corrections.
  • When a vehicle at the correct rear trim height hits a bump, the air suspension height sensor output will read low and high in addition to trim until the oscillations die out.
  • If the control module were to correct for these "bump induced readings", system duty cycle would increase unnecessarily.
  • The 45-second averaging interval not only eliminates corrections due to bumps, but also eliminates unneeded corrections resulting from braking, accelerating, and turning. The control module tabulates the air suspension height sensor readings, and does not begin a compress or vent operation until the air suspension height sensor (5359) reads low or high for 45 seconds consistently.
  • There are more restrictions on vent operations than there are on compress operations.
  • To eliminate the chance of catching a door on a curb as the vehicle vents down, the control module will not allow any venting to occur when a door is open.
  • The control module does not allow any vent operations for the first 45 seconds after the ignition switch (11572) has been turned to RUN.
    • Even if a vehicle is extremely high in the rear, DO NOT expect it to vent until the ignition switch has been turned to RUN for 45 seconds.

Jun 24, 2009 | 1994 Lincoln Town Car

2 Answers

VERY LOW REAR END


rear suspension ride leveler mslfunction. Check Air compressor function.

May 27, 2009 | 1992 Lincoln Town Car

1 Answer

Rear suspension stuck down. 96 crown victoria


these cars try to compensate for weight so the car will deflat the system to lower the rear when jacked up so when you put the car back down it almost touches the ground like a low rider, i think this is what you mean by suspension stuck down?? so all you have to do is start it. it should automatically adjust its self to the right inflation.bringing the car back up to position

Apr 10, 2009 | 1994 Lincoln Town Car

Not finding what you are looking for?
1999 Cadillac DeVille Logo

Related Topics:

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...