Vehicle is a 1973 CJ 5 jeep with 3 speed manual transmission, engine does not run. It was in neutral and pushed a few feet and then put in gear.
Now it is locked in gear and cannot get it in neutral.
The shifting lever will move like you were shifting gears but remains locked in gear.
SOURCE: 4T60e Transmission will not shift to D/OD
it sounds like the 3-4 clutches are out or the forward sprag has failed you may need a tranny rebuild
SOURCE: 92 Honda Accord, 5 speed, hard shifting into first & second gear.
First thing to do,try to pump your clutch before you shift into 1st gear then if you feel makes better, most probably you have problem with your hydraulic clutch system, check the clutch line if there is an evidence of fluid leaking or it could be internal leak.
Second thing to do, check your transmission oil, may be it' s too old or you use a thick oil thats why when cold its hard to shift then when the engine rich the normal temperature(warm) the oil become thin and the shifting will smooth. Remember the very old oil become thicken and the purity is gone and can cause of hard shifting. in this regards i suggest you to change the transmission oil and check the used oil if there is small peace of metals, then you are in big trouble,
SOURCE: f150 transmission neutralizes when shifts to overdrive
I have that exact same truck and transmission and My Transmission did the exact same thing about a year ago and there was some kind of snap ring inside the transmission that broke. I originally thought it had to be an electirical problem because the truck shifted fine until OD or if i turned OD off. The 4r70w is a light transmission and i would suggest you have a shift kit put in and they make a heavier kit to beef it up.. Sorry its probably not the new you were looking for.
SOURCE: 1995 Chevy S10 Blazer will not go into park.
theres a shift cable if its floor model,linkage for column model.
SOURCE: 1999 F350 crew cab 4x4 ford, gear shift lever
Ok ready to stand on your head under the dash?
It's doable... there is a flange connected to the gearshift lever under the steering column. If you remove the lower dash cover where the fuses are, you should be able to see it when you move the gear shift lever... look around on the floor of the truck to see if you dropped a star-headed bolt or two... these bolts worked loose on my superduty and made shifting very difficult..it was an easy fix... let me know how you do on it.
1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.
TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs
1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints
1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.
TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs
1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES
Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints
1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.
TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs
Oilman
513 views
Usually answered in minutes!
On the inside. Removed top plate, shift lever & yoke are attached to the plate. Then sprayed gears & yoke with WD40, replaced plate and now the lever will shift all gears and go into neutral.
Is the shift linkage on the outside or inside of the transmission on that one?
×