Question about 1991 Jeep Wrangler

1 Answer

What do you loosen to remove serpentine belt from 1991 jeep wrangler with ac and power steering. thanks 4 cyl. 2.5

Posted by gpeterson3 on

Ad

1 Answer

BILL RICHARDSON

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

There is an idler pulley close to the power steering. Loosen the bolt that goes through the front of the idler pulley first. Then you will see the head of a bolt looking up at you. Turn the bolt clockwise to tighten and counterclockwise to loosen. The pulley is attached to the threaded bolt and it moves the pulley up or down as needed to adjust the belt tension. When the belt is replaced turn the bolt until the belt is tight. Remember to check the belt again after a few hundred miles. A new belt will stretch and loosen.

Posted on Dec 08, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Free belt diagrams


http://serpentinebelthq.com/1991-jeep-wrangler-yj-4-0l-serpentine-belt-diagram/ her is a link for you to a diagram. I hope this helps

Jul 08, 2014 | 1991 Jeep Wrangler

1 Answer

How to install a serpentine belt on a 1991 jeep wrangler with a 2.5 engine without power steering


There should be a sticker in the engine compartment that shows the routing and you should be able to hold the tensioner back with a 3/8's ratchet with a long handle.

Jul 07, 2014 | 1991 Jeep Wrangler

2 Answers

I may have installed the serpentine belt incorrectly on my 1998 Jeep Wrangler with the 4.0 eng and AC. I am having problems with the engine overheating. Can you send me a diagram of the correct way to...


this is for a system with a/c. If you don't have a/c let me know and I will get you the correct one but i'm sure that you have a/c and power steering.


360dreamworx_55.gif

Aug 26, 2011 | 1998 Jeep Wrangler

1 Answer

Replaceing fan belt 1991 jeep renegade 4.0. no ac - how do yu add/remove tension?


at the front of the power steering pump you will see a nut over a slot loosen that up on the back side of the pump the is another bolt in a slot loosen that up and the one above it as well under the pump there is a bolt using a socket tighten this screw this will tighten the belt. Retighten all the other bolts wehn done do not over tighten the belt it will ruin the bearing and case early belt wear.

Dec 11, 2010 | 1991 Jeep Wrangler

1 Answer

How do you loosen the serpentine belt on a 1997 wrangler TJ?


loosen the bolts that hold the power steering pump to the bracket, then turn the transverse bolt under the pump to adjust tension.

Aug 26, 2010 | 1997 Jeep Wrangler

1 Answer

How do i replace serpentine belt on 1997 jeep wrangler


Adjustment is made by loosening the power steering pump. There is a transverse long bolt (jack bolt) right under the pump that is used for adjustment.

Aug 02, 2010 | 1999 Jeep Wrangler

1 Answer

Need routing diagram for serpentine belt - '98 Jeep Wrangler, straight six with and without A/C


Click of the following direct, Free Link. It has several Serpentine Diagrams, including the one for your 1998 Jeep Wrangler 4.0L In-Line 6-Cylinders based upon your Engine Options (AC/No AC, Power Steering/No Power Steering, etc.).
The Link Page ALSO has the 2.5L In-Line 4-Cylinder Serpentine Belt Diagrams with their various engine options.
Included are the with AC / without AC Routing.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!
http://www.2carpros.com/car_repair_information/year/1998/make/jeep/model/wrangler/1998_jeep_wrangler_drive_belt_routing_diagram.htm

Apr 13, 2010 | 1998 Jeep Wrangler

1 Answer

Where is the serpentine belt tensioner on a 1999 jeep wrangler with A/C?


most have a "jack screw" under the power steering pump. You loosen the pump mount bolts and adjust the screw underneath to tighten or loosen it.

Jan 18, 2010 | 1999 Jeep Wrangler

1 Answer

How to replace a serpentine belt on 1998 jeep wrangler


Should be the pulley underneath the power steering pulley. Loosen the nut, then back the bolt down the loosen the belt, tighten the bolt to tighten belt.

Jul 14, 2009 | 1999 Suzuki Esteem

Not finding what you are looking for?
1991 Jeep Wrangler Logo

478 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...