Question about 2006 Ford Fusion

1 Answer

Are there any online instructions for replacing the thermostat on the 2006 ford fusion 4 cyl. thank you much!

Posted by aturner950 on

Ad

1 Answer

Greg Bernett

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 2,989 Answers

2.3L Engine

  1. Raise and safely support the vehicle.
  2. Drain the cooling system.
  3. Remove the 3 bolts and reposition the thermostat housing to gain access to the hose clamps.
  4. Remove and discard the gasket.
    • To install, tighten the bolts to 10 Nm (89 lb-in).
  5. Disconnect the heater hose from the thermostat housing.
  6. Disconnect the lower radiator hose from the thermostat housing and remove the thermostat housing.

are there any online instructions for replacing - 6efb7cd.gif
Thermostat housing and related components—2.3L engine

To install:
  1. To install, reverse the removal procedure.
  2. Install a new thermostat housing gasket.
  3. Fill and bleed the cooling system

Posted on Dec 07, 2009

  • Greg Bernett
    Greg Bernett Dec 07, 2009

    3.0L Engines



    1. Raise and safely support the vehicle.


    2. Drain the cooling system.


    3. Disconnect the upper radiator-to-thermostat housing hose and position aside.


    4. Remove the 3 bolts, thermostat housing cover, O-ring seal and thermostat.


    5. Clean and inspect the O-ring seal. Install a new seal if necessary.



      • To install, tighten to 10 Nm (89 lb-in).





        NOTE


        Lubricate the thermostat O-ring seal with clean engine coolant.



    6. To install, reverse the removal procedure.


    7. Fill and bleed the cooling system




    Exploded view of the thermostat and related components—3.0L engine

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Ford Fusion 4 cyl.Engine light is on.Did diagnostic scan and it read P2004 Intake manifold runner bank 1a. There are 2 of these but dont know which one is bank 1a.


On a 2006 Ford Fusion with the 4 cylinder, there will only be one IMRC actuator. The V6 model has two. There is a solenoid and an actuator. You should check both of these for proper operation. The solenoid should click when it receives power and ground, and it controls vacuum to the actuator. The actuator should move when you apply or remove vacuum.
Also, when testing the actuator, it often takes more vacuum than you can produce with your mouth, so that is not an accurate test.

Oct 12, 2017 | Ford Cars & Trucks

1 Answer

Where do I connect the freon hose for my 2006 Fusion 4 cyl?


the low side port is locsted on the txv manifold ''on compressor'' that is the fitting you will need to find to be able to put more freon in it.

Sep 03, 2012 | 2006 Ford Fusion

1 Answer

2006 ford fusion. We're adding freon on our own. It says to be sure the compressor is on. Sounds stupid but need to be sure we're lookign int he right place, where is the compressor?


Hello! since I do not know which engine is in your Fusion I'm sending you a diagram of both;
2.3L (4 cyl.) and th3 3.0L (6 cyl.)....The compressor is encircled in both diagrams...If there is a correct amount of refrigerant the clutch (front of compressor) will engage....Guru....Saailer

saailer_110.gif

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Sep 03, 2011 | 2006 Ford Fusion

1 Answer

Where can i get a belt routing pic for 2006 ford fusion 4 cyl


Usually there is a Routing Diagram under your hood somewhere around if you look on the firewall or in front of the engine, But any how hope this picture is the same of what you looking for. Good luck tgv1501_18.jpg

Dec 18, 2010 | 2006 Ford Fusion

2 Answers

What is error code P0128 on 2006 Ford Fusion SE, 4 cyl, auto


P0128 is the fault code to check 1.the coolant level 2. thermostat defective 3. ECT (engine coolant temperature) sensor defective

Nov 13, 2010 | 2006 Ford Fusion

1 Answer

P0128 code on 2006 ford fusion. add coolant or replace thermostat?


Your vehicle needs a thermostat. It is a pretty simple repair. Its under the left side of the intake manifold. You have to get one of the bolts from the bottom and the other two from the top.

Sep 25, 2010 | 2006 Ford Fusion

2 Answers

How do you fix a P0128 code on a 2006 Ford Fusion?


Upstream HO2S Sensors Swapped or this one
P0128....Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature) now if this a 2006 model built for the europeon market then your code reader is a waste of time as it will never read the correct codes and if your really lucky it could lock up the immobilisor as well this is to prevent general garages from doing any repairs so just take it back to a ford garage

Jul 30, 2010 | 2006 Ford Fusion

1 Answer

Code P0128 ford, fusion 2006 4 cly


I had the same code. It means your engine coolant temp. is too low. That means your thermostat needs to be changed. Get the Ford Motorcraft one. It comes with the entire housing. Have a mechanic replace it. It is a real bugger to get to.

Mar 28, 2010 | 2006 Ford Fusion

1 Answer

Moaning, whining sound when the clutch is depressed. Gets louder when revving the engine. 2006 Ford Fusion 4 cyl 5 speed manual. I think it might be the throwout bearing but not sure. Don't know if the...


last one or i will not get up for work tomorrow,its the thrust bearing ,**** plastic fittings used ,when it goes completely ,just renew the whole lot ,if you drop subframe then they are easy to change ,about 2 hrs, but you mush drop the subframe ,its only 4 bolts two either side

Jan 12, 2010 | 2006 Ford Fusion

Not finding what you are looking for?
2006 Ford Fusion Logo

6,545 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...