Question about 1989 Mazda 323

1 Answer

1989 Mazda truck 4 cyl B2200 series -- clutch is gone or fluid. Are these clutches hydraulic? Very ignorant when comes to mechanics. If fluid, where do I check the fluid? I press clutch pedal to floor but there is no clutch to shift gears.

Posted by rogerbaker1 on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points
    MVP:

    An expert that got 5 achievements.
    Governor:

    An expert whose answer got voted for 20 times.
    New Friend:

    An expert that has 1 follower.

  • Expert
  • 136 Answers

Check under your hood for a another cap looks similar to a brake fluid resouvior see if its empty.if it is you probably blown the seal on your slave cylinder its what throws your clutch out.

Posted on Dec 07, 2009

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Mazda B 2200 will not go in gear?
hydraulic clutch system
if the clutch master cylinder is full of brake fluid
master or slave is by passing

shift linkage out of adjustment
worn clutch or pressure plate damaged



26235114-o4qxaik4ragwwyoapewpjppp-5-0.jpg

26235114-o4qxaik4ragwwyoapewpjppp-5-1.jpg

Jul 10, 2016 | 1988 Mazda B2200

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up
If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

2 Answers

1990 mazda b2200 clutch sticks to floor
Check the fluid in the hydraulic clutch resevoir.

Aug 10, 2011 | 1988 Mazda B2200

3 Answers

Mazda e2200 clutch repair: feels like I still have some kind of pedal springback, but without much force. No clutch at all. I assume it is hydraulic, but the only reservoir I see is for the brakes. That is...
Yes, hydraulic--check again--fender side of brake master. Slave is usual cause of leak that eventually causes master reservoir to go dry and start drawing air. Check slave for leak. If leaking, replace slave and bleed system. Make sure to bench-bleed slave before installation by opening bleeder and pouring fluid into line port.

jturcotte_373.gif
  1. Raise and support the front end on jackstands.
  2. Back off the flare nut on the fluid pipe to free the slave cylinder hose.
  3. Pull off the hose-to-bracket retaining clip and pull the hose from the bracket. Cap the pipe to prevent fluid loss.
  4. Unbolt and remove the slave cylinder.
  5. Installation is the reverse of removal. Tighten the bolt to 12-17 ft. lbs. (16-23 Nm).

Dec 04, 2010 | 1988 Mazda B2200

2 Answers

The hydraulic clutch stopped working.It won't shift.There is no pressure on the clutch whne you push it down.
The clutch hydraulic system is very small. Check the resevoir is full. If empty fill. Try clutch. Still problem ? Bleed the clutch slave cylinder at the trans bleeder. You dont bleed this clutch like brakes pumping up several times. Have someone push clutch to the floor and hold it there, then you open and close bleeder while keeping pedal to the floor. Check the fluid level every time you open/close the bleeder as this system is so small and will empty quick.

Nov 16, 2010 | 1994 Mazda 2WD B Series Pickup

2 Answers

The brake fluid for the clutch runs out very quickly creating a clutch fail
From where it is running? Master cyl ? Cyl on the transmission? Hose?
That's an exhaustive list of choices. Replace whatever is leaking.

Oct 01, 2009 | 1989 Jeep Wrangler

1 Answer

1989 Mazda mx-6=gear shift
This make and model has hydraulic clutch.Most likely clutch master or slave cylinder gone bad.Look to see if any fluid is leaking out of slave cylinder,or clutch master.There may not be any,but this would help decide witch one to replace if there was one leaking.This would be the problem,one or the other.If I can help,let me know.

Aug 24, 2009 | 1989 Mazda MX-6

5 Answers

Stuck clutch pedal on a Mazda B series truck
Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Jul 11, 2009 | 1988 Mazda B2200

1 Answer

Clutch pedal low near floor, can the clutch be adjusted?
hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Feb 02, 2009 | 2005 Hyundai Accent

2 Answers

1989 mazda astina 323 5 spd manual clutch fluid??
open your bonnet check to see @ gearbox if the-res is cable, or a cylinder, the cable is Usualy visible on the top of the gearbox if theres a cable theres no clutch flu-ed needed. Note that your gearbox uses oil. Usualy on older models like 1989 the use a clutch cable no flu-ed needed

Jan 03, 2009 | 1989 Mazda 323

Not finding what you are looking for?

View Most Popular

1989 323

  • Cars & Trucks

Related Question

Mazda B 2200 will not go in gear?

  • 1988 Mazda B2200

Open Questions:

0 Answers

carburetor diagram overheating

Mar 19, 2014 | 1989 Mazda 323

0 Answers

mazda astina 1999 no visible spark what now

Nov 27, 2013 | 1989 Mazda 323

0 Answers

1995 mazda astina where would the compliance plate be?

Nov 14, 2013 | 1989 Mazda 323

0 Answers

My 89 mazda 323 has a leak, and the transition fluid is just pooring out. Also.. My 89 Mazda 323 has a leak, and the transition fluid is just pouring out. Also, this morning i had to move it to a spot i could see the leak better, and smoke was just pouring out of the exhaust pipe! What could be causing the smoke, and whats the best way to find and stop the leak?

Mar 04, 2018 | 1989 Mazda 323

See all 1989 Mazda 323 Questions

Related Topics

Cars & Trucks Logo

Related Topics:

467 people viewed this question

Ask a Question

Usually answered in minutes!

Popular Questions

1994 Mazda 323

1990 Mazda 323

1994 Mazda 323

Mazda 323 Cars & Trucks

1994 Mazda 323

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

6528 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...