Wiring schematic for tail lights

What's a DHS ?
Stop Lamps

The STOP LP fuse in the rear fuse block supplies battery positive voltage to the normally open stop lamp switch. When the brake pedal is pressed, the stop lamp switch contacts close and battery positive voltage is supplied to the center high mounted stop lamp (CHMSL) and the turn signal/hazard flasher module stop lamp switch signal input. In response to this input the turn signal/hazard flasher module supplies battery positive voltage to the left and right LED tail lamp assemblies. The CHMSL and left tail lamp have ground at G402. The right tail lamp has ground at G401. The stop lamps illuminate when they receive both power and ground.
es battery positive voltage to the left and right LED tail lamp assemblies. The CHMSL and left tail lamp have ground at G402. The right tail lamp has ground at G401. The stop lamps illuminate when they receive both power and ground.

Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

In the diagram for rear lamp, the top wires are voltage, the bottom black wire is ground. The brown wire on either side should be tail lamps, goes hot when you turn on the headlamp switch. The other top wire on either should be for turn signal. With everything turned on, is there voltage on that wire?
Because the front works and the rear don't, possible wiring circuit problem? The voltage for turn signals comes from bcm. The bcm knows when you turn on turn signal switch, either side, then the bcm sends voltage to turn signal lamp at the rear and front.

1) Open trunk
2) Remove small round plastic access panel with a flat tip screw driver by prying open
3) Remove flat tip screw holding tail light assembly
4) Remove tail light assembly by pulling outward, careful not to break plastic guide/nub
5) Disconnect wiring connectors
6) Remove plastic housing access plate on back of tail light assembly by twisting/turning tabs until they click and then lift access plate from tail light assembly
7) When viewing the the bulbs, the turn signal bulb is the bottom left bulb
8) Install in reverse order, ensuring tail light seal seats properly during installation

Use the wiring schematic to follow the wires and check for any breakage or burnt wires. Repair any breakage and recheck. Check all grounds in the circuit as well; a faulty ground can cause total loss of lights.
Check the brake light switch near the break pedal. Use a voltmeter to make certain the voltage is correct with switch engaged and disengaged. Check the grommet that depresses the switch as well. Repair any issues and recheck.
Key Fob Programming
ECU Tuning Software
Immo Emulator
Car Key Chips
Airbag Reset Tool

Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Power for left rear turn signal is dark blue
Power for left rear tail light is brown
Power for left rear stop light is light blue.
Black is ground

no disrespect but....
Check the book and make sure you are using the proper bulbs on all sides. (3957 looks just like 3956 but wont work right)

There was a recall on this, take to the dealer and they will replace the whole socket on this.

exactly what does it do? please explain what happens when you press the brake turn on the light than brake signals ect.....